The flowrate between tank A and tank B shown in the figure below is to be increased by 15% (i.e, from Q to 1.15Q) by the addition of a second pipe (indicated by the dotted lines) running from node C to tank B. If the elevation of the free surface in tank A is 15 ft above that in tank B, determine the diameter, D, of this new pipe. Neglect minor losses and assume that the friction factor for each pipe is 0.02. 6n duneter 600 k -i. diamt s00 n long Dnater ,00 lo D- 4.4315176317 ft

The flowrate between tank A and tank B shown in the figure below is to be increased by 15% (i.e, from Q to 1.15Q) by the addition of a second pipe (indicated by the dotted lines) running from node C to tank B. If the elevation of the free surface in tank A is 15 ft above that in tank B, determine the diameter, D, of this new pipe. Neglect minor losses and assume that the friction factor for each pipe is 0.02. 6n duneter 600 k -i. diamt s00 n long Dnater ,00 lo D- 4.4315176317 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
Water flows through the galvanized iron pipe system whose diameter is 0.75 inches and flow rate is 0.020 cfs. Do you agree with the fact that friction losses in the straight parts of the piping system are negligible with respect to losses to fittings?
A 15-ft-diameter tank discharges water at 50 F through a 2-in.-diameter sharp edged orifice. If the initial water depth in the tank is 10 ft and the tank is continuously pressurized to 50 psi, how long will it take to empty the tank?
Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump, it then flows horizontally through 100m of piping, and out into the atmosphere. If there are 2 standard elbows and one wide open gate valve in the discharge line, determine a) all friction losses in the system and b) the power requirement of the pump if it is to maintain 0.8 cubic meters per minute of flow. Assume a pump efficiency of 55%, and that friction is negligible in the pump suction line.
From the attached figure, determine the flow rate in each pipe taking into account that minor losses are negligible.
A horizontal nozzle discharges water into the atmosphere as shown in the figure, being the relative pressure at point 1 equal to p1 = 20 kPa A Pitot tube connected to a mercury manometer is inserted into the flow in area section A1 indicating a height difference h = 0.02 m. For this reading indicated in the Pitot tube, determine the speed in the Area A1 section of the nozzle. For docking block sizing it is necessary to determine the force that the nozzle applies to the fluid. Calculate the component of this force in the x direction. Data: D1 = 0,075 m; D2 = 0,055 m; θ = 30° ; dHg = 13,6.
Oil relative density (rd = 0.88) flows in an inclined pipe at a rate of 0.15 m/s as shown in Fig. If the differential reading in the mercury manometer is 915 mm, calculate the power that the pump supplies to the oil if head losses are negligible.
The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.
A diverging tube discharges water from reservoir at a depth of 10m below the water surface. The diameter of the tube graduallyincreases from 150 mm at the throat to 225 mm at the outlet.Neglecting friction, determine the maximum possible rate ofdischarge through this tube.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.