Engineering mechanics statics Q.1) A plane truss is loaded as shown in thefigure. What is magnitude of force in themember CD and is it in compression ortension100 N100 NBD2020v3(A) 692.82 N, compression(B) 692.82 N, Tension(C) 1385.64 N, Compression(D) 1385.64 N, Tension(E) No one of above write your answer20EA500 N20

use method of section cut a section xx Take moment about point C 500*20 +100*10 = FBD*203 FBD =…

Q.1) A plane truss is loaded as shown in the figure. What is magnitude of force in the member CD and is it in compression or 100 N 100 N B D 20 tension 20V3 (A) 692.82 N, compression (B) 692.82 N, Tension (C) 1385.64 N, Compression (D) 1385.64 N, Tension (E) No one of above write your answer - 20 20 E A C 500 N

Q.1) A plane truss is loaded as shown in the figure. What is magnitude of force in the member CD and is it in compression or 100 N 100 N B D 20 tension 20V3 (A) 692.82 N, compression (B) 692.82 N, Tension (C) 1385.64 N, Compression (D) 1385.64 N, Tension (E) No one of above write your answer - 20 20 E A C 500 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
Dr. Alexander is holding a briefcase with straight arm. Assume weight of the briefcase FB = 35 N, weight of the forearm FFA = 10 N, weight of the upper arm FUA = 15 N, moment arm of FB = 0.45 m, moment arm of FFA = 0.30 m, moment arm of FUA = 0.11 m, and moment arm of Fm = 0.03 m. Also, FM is 35 degrees above the horizontal. Calculate (1) muscle force FM, and (2) joint reaction forces Fj,x and Fj,y
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
Ancient pyramid builders are balancinga uniform rectangular stoneslab of weight w, tipped at anangle u above the horizontal, usinga rope (Fig.). The rope isheld by five workers who share theforce equally. (a) If u = 20.0°, whatforce does each worker exert on therope? (b) As u increases, does eachworker have to exert more or lessforce than in part (a), assuming theydo not change the angle of the rope? Why? (c) At what angle do theworkers need to exert no force to balance the slab? What happens if uexceeds this value?
A uniform horizontal beam with a length of 1.7 m and a weight of 200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 35.0° with the horizontal. If a crate of mass (M) 87 kg hanged 1.7 m from the wall, find the tension in the cable, as well as the magnitude and direction of the resultant force exerted by the wall on the beam.
A 110-kg uniform ladder is tied at its bottom on the wall using a wire shown in the figure. The floor is frictionless, while the wall is rough. The maximum tension on the wire is 180 N. (a) What is the normal force exerted by the wall on the ladder? (b) What is the frictional force exerted by the wall to the ladder?
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
In engineering, a truss is a structure that "consists of two-force members only, where the members are organized so that the assemblage as a whole behaves as a single object”. Based from Figure 2 below, determine the force in each member of the truss, and state if the members are in tension or compression. Set θ = 0°.
Two weights are connectedby a very light, flexible cord that passesover an 80.0 N frictionless pulley of radius0.300 m. The pulley is a solid uniformdisk and is supported by a hookconnected to the ceiling (Fig.).What force does the ceiling exert on thehook?