Q.1 The dimensions and configuration of the four bar mechanism, shown in Fig. 1 are as follows : PA = 300 mm; P,B = 360 mm; AB = 360 mm, and P,P2 = 600 mm. The angle AP,P2 = 60°. The crank PA has an angular velocity of 10 rad/s, anticlockwise. Determine the angular velocities and angular accelerations of P,B, and AB and the velocity and acceleration of the joint B B 360 mm A 360 mm 60° TTTTI P1 P2 600 mm Fig. 1

Q.1 The dimensions and configuration of the four bar mechanism, shown in Fig. 1 are as follows : PA = 300 mm; P,B = 360 mm; AB = 360 mm, and P,P2 = 600 mm. The angle AP,P2 = 60°. The crank PA has an angular velocity of 10 rad/s, anticlockwise. Determine the angular velocities and angular accelerations of P,B, and AB and the velocity and acceleration of the joint B B 360 mm A 360 mm 60° TTTTI P1 P2 600 mm Fig. 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks?
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
Consider the slider-crank mechanism shown. Crank AB is 0.500 m long and is rotating counterclockwise at 3.00 rad/s. Rod BD is 1.500 m long. 1. Which of the following gives the closest value of the speed of end B of crank AB? 2. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion?
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
Consider a person holding a vacuum cleaner (idealized as Bar AB). The point where the person holds the handle (point A) is constrained to move along the vertical and has a velocity of 0.12 m/s downwards and is increasing its speed at a constant rate of 0.4 m/s2. This is to move the tail end (Point B) of the cleaner. The tail end of the cleaner has a velocity of 0.0840 m/s to the right and the vacuum cleaner has an angular velocity of 0.0586 rad/s.a) What is the the magnitude of the angular acceleration of the vacuum cleaner (Bar AB)? (1.313, 3.5, 0.875, 1.969) b) What is the magnitude of the acceleration of block B? (0.521, 0.270, 0.1929)
Lever is attached to a gear of radius R_1 = 0.50 in and moment of inertia I_1 = 1.0 kg m^2. This gear meshes with a second gear of radius R_2 = 1.0 m and moment of inertia I_2 = 16.0 kgm^2. Each gear rotates about a fixed axis running through its center. Force F = 2.0 N is applied on the lever at a distance of 1.0 m from the center of the gear. What is the angular acceleration of each gear?
A shaft is rotating at a uniform angular speed. Four masses M1, M2, and M3 and M4 of magnitudes 300kg, 450kg, 360kg, 390kg respectively are attached rigidly to the shaft. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mmand 300mm respectively. The angle made by these masses with horizontal are 0°.45°, 120°and 255°respectively. Find-(i) the magnitude of balancing mass (ii) the position of balancing mass if its radius of rotation is 200mm.
The piston of a 60° twin V-engine has strokes of 126 mm. The connecting rodsdriving a common crank has a length of 202 mm. The mass of the reciprocatingparts per cylinder is 1.2 kg and the speed of the crank shaft is 2000 rpm. Determinethe magnitude of the primary and secondary forces.
Find: 1-- Displacement 2- Velocity 3-Acceleration for slider crank When, ? = 100 rad/???2 R=6.3cm L=26.1cm ? = 100 ???/???
Mechanism shown consists of two 8-pound rods AB and CD. each and a 10 lab AD bar. When θ = 0 °, the rod AB rotates with a velocity angular of 2 rad / s. If a torque M = 15 lb * ft is applied to the rod CD and to the rod AD is applied a force P = 20 lb., calculate the angular velocity of the bar AB at the instant that θ = 40 °
A 5.32-kg disk A of radius 0.445 m initially rotating counter-clockwise at 436 rev/min is engaged with a 6.72-kg disk B of radius 0.275 m initially rotating clockwise at 528 rev/min, where the moment of inertia of a disk is given as I = ½ mi?. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disks. Remember to show clearly the equations that you use!!'
Consider the mechanism shown. Members PQ and QR are joined by a hinge at Q. End P of member PQ is pin-supported and end R of member QR is constrained to move along a horizontal surface. Member PQ rotates clockwise at a constant rate of 12 rad/s. Member QR rotates counterclockwise at a rate of 3.84 rad/s. Which of the following gives the closest value to the magnitude of the angular acceleration of rod QR? 9.16, 6.18, 1.609, 35.2 rad/s^2?? Which of the following gives the closest value to the magnitude of the acceleration of point R? 3.13, 9.89, 10.28, 12.88 m/s^2??