The dimensions of the various links of a mechanism, as shown in Fig. 3, are as follows: OA = 0.3 m: AB = 1 m; CD 0.8 m; and AC CB. If the crank OA rotates at 100 rpm. in the anticlockwise direction, find, for the given configuration: 1. velocity and acceleration of B and D; 2. angular acceleration of the links AB and CD. 45C0 0.6 m-

The dimensions of the various links of a mechanism, as shown in Fig. 3, are as follows: OA = 0.3 m: AB = 1 m; CD 0.8 m; and AC CB. If the crank OA rotates at 100 rpm. in the anticlockwise direction, find, for the given configuration: 1. velocity and acceleration of B and D; 2. angular acceleration of the links AB and CD. 45C0 0.6 m-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks?
find an acceleration of the center of the beam (marked as a blue point) which is connecting both wheels , if it is known that linear velocity ot the wheels v=100km/h, r=0,8m and the distance drom the center of the wheel and the pont where the beam is connected (marked as red red distance)=0,4m, there is no slipping between wheels and the ground
Figure shown represents a schematic diagram of a Porter governor. Each fly ball weighs 16.1 lb and the central weight D is 40 lb. Determine the rotational speed in rpm about the vertical axis AD at which the weight D begins to rise. Answer: n=109 rpm
Consider the slider-crank mechanism shown. Crank AB is 0.500 m long and is rotating counterclockwise at 3.00 rad/s. Rod BD is 1.500 m long. 1. Which of the following gives the closest value of the speed of end B of crank AB? 2. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion?
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the acceleration of sldier block C?
Most gasoline engines in today's automobiles are belt driven. This means that the crankshaft, a rod which rotates and drives the pistons, is timed to the camshaft, the mechanism which actuates the valves, by means of a belt. Starting from rest, assume it takes t=0.0320s for a crankshaft with a radius of r1=3.25cm to reach 1750 rpm. If the belt does not stretch or slip, calculate the angular acceleration of crankshaft 2 of the larger camshaft, which has a radius of r2=6.50 cm, during this time period.
A, B, C and D are the four masses carried by a shaft in this order. Radii of rotation of the masses are 20cm, 25 cm, 10 cm and 15 cm respectively. The masses of B, C and D are 3 kg, 5 kg and 4 kg respectively.The planes containing B and C are 25 cm apart. Angle between B and C is 90o and between B and D is220o measured in anticlockwise direction. For complete dynamic balance, find (i) The mass and angularposition of A, (ii) The position of planes A and D.
In the figure, Pulley A, rotating at 20 rad/s, controls the motion of Pulley B. The motor of pulley A is cut off, and friction eventually brings the pulleys to a stop with an angular acceleration of α = -2.5t rad/s2. If there is no slippage, determine: a. The angular velocity of B with respect to time b. The angular displacement of B during the deceleration c. The acceleration of point C with respect to time
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. Which vector equation relates the accelerations of points B and C ?
Consider a person holding a vacuum cleaner (idealized as Bar AB). The point where the person holds the handle (point A) is constrained to move along the vertical and has a velocity of 0.12 m/s downwards and is increasing its speed at a constant rate of 0.4 m/s2. This is to move the tail end (Point B) of the cleaner. The tail end of the cleaner has a velocity of 0.0840 m/s to the right and the vacuum cleaner has an angular velocity of 0.0586 rad/s.a) What is the the magnitude of the angular acceleration of the vacuum cleaner (Bar AB)? (1.313, 3.5, 0.875, 1.969) b) What is the magnitude of the acceleration of block B? (0.521, 0.270, 0.1929)
Lever is attached to a gear of radius R_1 = 0.50 in and moment of inertia I_1 = 1.0 kg m^2. This gear meshes with a second gear of radius R_2 = 1.0 m and moment of inertia I_2 = 16.0 kgm^2. Each gear rotates about a fixed axis running through its center. Force F = 2.0 N is applied on the lever at a distance of 1.0 m from the center of the gear. What is the angular acceleration of each gear?