Q.2 A skuntmator has asupply Voltiga = 200 Volt , armature resistance =4 S2. At certain lond the motor speed=1200 RPM and the moor takes a currant of 10 ampere ram h supply.. The field Current= 0.5ampen.Find: starting targue? i no-lond spedis lond torgue? ; Th speed when the lond takes S Amperr from the sepl4 ? %3D

Q.2 A skuntmator has asupply Voltiga = 200 Volt , armature resistance =4 S2. At certain lond the motor speed=1200 RPM and the moor takes a currant of 10 ampere ram h supply.. The field Current= 0.5ampen.Find: starting targue? i no-lond spedis lond torgue? ; Th speed when the lond takes S Amperr from the sepl4 ? %3D

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter33: Four-speed, Two-winding (consequent Pole) Motor Controllers

Section: Chapter Questions

Problem 7SQ: Why are different motor connections shown for what appears to be the same motor in the various...

See similar textbooks

Similar questions

A shunt DC generator has no load terminal voltage of 140V. Armature resistance is 1ohm and shunt field resistance is 50ohms. Calculate: (i) Induced voltage (ii) A load is now connected to the terminals that starts drawing 2A current and terminal voltage drops to 130V. Calculate the new value of the induced voltage Make sure to draw equivalent circuits for (i) and (ii)
Q/Two dc generators A and B has the following characteristics:GA: rated voltage=150 volt: rated carrent=30Ampere: armature resistance (0.4Ω).GB:no_lond voltage=160Volt: rated carrent=20Ampere: armature resistance=(0.6Ω).The generators are connected in paralled. Draw the circuit diagram, then find:no_load circulating current and no_load voltage?At what carrent the generator B will Be floating? The maximum possible land power
A 500-kw 600-volt 10-pole generator has an armature with 108 slots, 324 commutator segments, and a simplex-lap winding with a total of 648 conductors. Calculate: (a) the number of conductors per slot; (b) the number of winding elements per coil; (c) the number of turns per winding element; (d) the full-load current per conductor; (e) the current per brush arm. (Our lesson is DC GENERATORS in the subject ELECTRICAL MACHINE 1) (I NEED A CLEAN ANSWER AND SOLUTION. THANK YOU SO MUCH
Write the solution neatly. A 230 V d.c. shunt motor, having an armature resistance of 0.05 ohm and a fieldresistance of 75 ohms, draws a line current of 7 A while running light at 1120 rpm. Determine the motor efficiency when the line current at a given load is 46 A. Answer % = 83.92 %
The following figure shows the cross-section structure of a 4/2 pole variable reluctancemotor with dimensions as R=3.8 cm, α=60o, β=45o , g=0.254 mm, and D=13 cm. The polesof each phase winding are connected in series such that there are a total of N=100 turns(50 turns per pole) in each phase winding. Assume that rotor and stator to be of infinitemagnetic permeability. Plot the torque, assuming (i) i1=I1 and i2=0; and (ii) i1=0 and i2= I2
Question 11 Design a Duplex layer simplex lap winding DC machine armature winding by providing a complete wiring diagram with the following Number of Poles: 2 Number of Slots; 8 Thank you and Godbless ASAP pleasee
ANSWER THE PROBLEM SOLVING, MAKE SURE YOUR ANSWERS ARE IN 4 DECIMAL PLACES. SHOW YOUR COMPLETE SOLUTION. 3. A shunt generator is connected to a load that draws 30 KW on full-load. The armature resistance is 0.1 ohm. If the power generated in the armature is 33.50 KW, and the shunt field resistance is 80 ohms, determine the: A. Variable copper loss B. Constant loss C. Maximum efficiency
DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.) A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. What is the total losses? a. 2512 W b. 1756 W c. 3718 W d. 3042 W
The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. Theresistance of the armature circuit is 0.3 ohm. When the motor current is 30 A, speedis 900 r.p.m. If the current reduces to 20 A at lower speed, what arrangement shouldbe made? Neglect any effect not included in the data given. (Ans.3.833 ohms)
Why are different motor connections shown for what appears to be the same motor in the various diagrams in Figure 332? FIG. 332 Typical arrangements for four-speed, three-phase, two-winding motors.
5. Calculate the flux per pole required on full-load for a 50 kW, 400 V, 8-pole, 600 r.p.m. d.c. shunt generator with 256 conductors arranged in a lap-connected winding. The armature winding resistances is 0.1 Ω, the shunt field resistance is 200 Ω and there is a brush contact voltage drop of 1 V at each brush on full-load. Subject Electrical Machine 1
A 220V shunt generator has armature resistance of 0.2 ohms and a shunt resistance of 44 ohms. At rated load, the driving engine develops 62.5HP. if the iron and friction losses amount 1600W, how much is the current delivered to the load at rated condition?