Q.2 For the circuit shown:1) Calculate Req.2) Find the supply voltage (V)3) Calculate I, I4) Find the voltage across 60 resistance.5) Calculate the power consumed by 40 resistance.I10 Ω10 Ω3 A50

We redraw the circuit in simplified form

Q.2 For the circuit shown: 1) Calculate Req. 2) Find the supply voltage (V) 3) Calculate I, I, 4) Find the voltage across 62 resistance. 5) Calculate the power consumed by 4n resistance. I, 5Ω 10 Ω 42 10 Ω ЗА 50

Q.2 For the circuit shown: 1) Calculate Req. 2) Find the supply voltage (V) 3) Calculate I, I, 4) Find the voltage across 62 resistance. 5) Calculate the power consumed by 4n resistance. I, 5Ω 10 Ω 42 10 Ω ЗА 50

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 44P: Consider the circuit shown in the preceding problem. Write equations for the power supplied by the...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P18.11. Find (a) the potential difference between points a and b and (b) the current in the 20.0- resistor. Figure P18.11
The rather simple circuit shown below is known as a voltage divider. The symbol consisting of three horizontal lines is represents “ground” and can be defined as the point where the potential is zero. The voltage divider is widely used in circuits and a single voltage source can be used to provide reduced voltage to a load resistor as shown in the second part of the figure, (a) What is the output voltage Vout of circuit (a) in terms of R1,R2,andVin (b) What is the output voltage Vout of circuit (b) in terms of R1,R2,RLandVin
Referring to the example combining series and parallel circuits and Figure 10.16, calculate in the followingtwo different ways: (a) from the known values of Iand I2 (b) using Ohm’s law for R2 In both parts, explicitlyshow how you follow the steps in the Problem-Solving Strategy: Series and Parallel Resistors.
Consider the circuit shown below, (a) Find the current through each resistor, (b) Check the calculations by analyzing the power in the circuit.
A 0.0200- ammeter is placed in series with a 10.00- resistor in a circuit, (a) Draw a circuit diagram of the connection, (b) Calculate the resistance of the combination, (c) If the voltage is kept the same across the combination as it was through the 10.00- resistor alone, what is the percent decrease in current? (d) If the current is kept the same through the combination as it was through the 10.00-resistor alone, what is the percent increase in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
Referring to the example combining series and parallel circuits and Figure 21.6, calculate I3in the following two different ways: (a) from the known values of I and I2 ; (b) using Ohm’s law for R3. In both parts explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
Consider the circuit shown below. The terminal voltage of the battery is V = 18.00 V. (a) Find the equivalent resistance of the circuit, (b) Find the current through each resistor, (c) Find the potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the power supplied by the battery.
Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10
The following statements are related to household circuits and electrical safety. Determine whether each statement is true (T) or false (F). (a) Circuit breakers are wired in series with the outlets they protect. (b) A circuit breaker rated at 20 A provides a constant current of 20 A to each outlet in the circuit. (c) Three-wire electrical cords help prevent dangerous electrical shocks by grounding the case of a device.
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
The label or a portable radio recommends the use of rechargeable nickel-cadmium cells (nicads), although they have a 1.25-V emf while alkaline cells have a 1.58-V emf. The radio has a 3.20- resistance, (a) Draw a circuit diagram ot the radio and its batteries. Now, calculate the power delivered to the radio, (b) When using Nicad cells each having an internal resistance of 0.0400O. (c) When using alkaline cells each having an internal resistance of 0.200 . (d) Does this difference seem significant, considering that the radio s effective resistance is lowered when its volume is turned up?