Q.2) Group 2 (a) Use Thevenin's theorem to find io (current on the 10 ohm) in the circuit shown in Figure 2 a and draw Thevenin's equivalent circuit. (b) Find the power supplied by the independent voltage source. (Figure 2 a) (c) Find the total power dissipated in the two resistors. (Figure 2 a) (d) Find the Vo (voltage on the 2-ohm resistor) by using nodal analysis. (Figure 2 b) Group 2 10 V 552 www Figure 2 a 102 wa 4i。 b 10 V Good luck! + 492 ww 202 + 802 Figure 2 b 10 (2 2 A 2%

Q.2) Group 2 (a) Use Thevenin's theorem to find io (current on the 10 ohm) in the circuit shown in Figure 2 a and draw Thevenin's equivalent circuit. (b) Find the power supplied by the independent voltage source. (Figure 2 a) (c) Find the total power dissipated in the two resistors. (Figure 2 a) (d) Find the Vo (voltage on the 2-ohm resistor) by using nodal analysis. (Figure 2 b) Group 2 10 V 552 www Figure 2 a 102 wa 4i。 b 10 V Good luck! + 492 ww 202 + 802 Figure 2 b 10 (2 2 A 2%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of two resistors, one is 30-Ohm and the other is R being unknown. Determine the value of R if: (a) the power dissipated in 6-Ohm resistor is equal to the power in the parallel combination; (b) he power in 6-Ohm is equal to the power of in R; (c) value of R maximum power transfer.Hint: To maximize power in R, use differentiation
Given that Vs is 75 V, R1 is 9 Ohm, R2 is 3 Ohm, R3 is 8 Ohm and R4 is 20 Ohm. Find equivalent VTh with respect to terminals a, b in the circuit shown. (Unit: V) Find equivalent RTh with respect to terminals a, b in the circuit shown. (Unit: Ohm)
In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of two resistors, one is 30-Ohm and the other is R being unknown. Determine the value of R maximum power transfer. Hint: To maximize power in R, use differentiation
Q2- For PV /Battery Stand-Alone System, the system nominal volage=120V. The days of autonomy=12 day. The total daily load=34Ah/day. 1- Find the battery capacity. Hinit: take capacity to be 1.5 of calculated value. 2- For PV panel of V ,p,=24V and lLyp,=6.1A, A:L=1.5, sun hours(SH=4h) and efficiency of system=70%. a-Find the number of PV panels for each string(N,). b- Find the number of strings (Ny). c- Find the total number of PV panels used.
Solve this question1)In concentrating solar power - central receiver, one of the following advantages is wrong comparing to parabolic troughSelect one:a. it requires less gross land area and less capital costb. None of thesec. No need for miles of tubes absorber tubes circulating HTFd. Less water usee. Achieves higher temperature and pressure2) The temperatures necessary to get sufficient efficiency to convert the earth’s heat to electrical power is:Select one:a. 160 °Cb. 230 °Cc. 130 °Cd. None of thesee. 200 °C
a) A 380V, 7.5kW electric water pump of power factor 0.8 lagging and efficiency of 85% will be wired by an armoured XLPE insulated copper cable. The circuit will be run on cable tray with three other similar circuits at an ambient temperature of 40℃. MCCB will be used as the overcurrent protective device for the circuit. The estimated length of the circuit for the machine is 50m. i) Determine the minimum rating of MCCB for the circuit, available MCCB rating are 25A, 30A, 40A, 50A ii) Determine the minimum cable size of the circuit if the allowable voltage drop of the circuit is 1.5% of the nominal supply voltage?
Use node voltage analysis to determine values forI1, I2, and I3. If a current has a negative value, then the reference direction chosen was incorrect and the current is really positive in the opposite direction. Your answer is allowed to be negative; for example, if you find that I2=−3 mA, that is an acceptable answer.
Lrocedure A- Kirchhoff's voltage law: The circuit in Figure 2 will be used o test the valdity of Kirchhoffs voltage law, Figure (2) Construct the circuit as shown in the figure (2). Measure the power supply output voltage and the potential drops across each of the thrae resistors. Record these measurements in your lab notebook as in the following table: University of Ti-Qar/ Departmnt of Elctricl aad Fectronlc Enginearing / Prepared by M 5¢ Al Karvem Soes 1+ Stage: Fundamentals of Flectrical Engineering | Lob 3 - Kirchhoff's Laws. 201520, Table 1; data collected for testing the validity of Kirchhot?s voltage law. 3)From your experimental data (table 2), calculate the total current into the node point P. Now calculate the total current out of the node point P along with its uncertainty. Does the current into the node agree with the current out of the node within experimental uncertainty?
A) Use any analysis method to calculate the voltage Vo and the power dissipated by the dependent source indicating whether the dependent source absorbs or generates power.Indicate the method you used in the analysis and explain your procedure.B)If the 2 Ω resistor, where the voltage Vx is defined, is short-circuited, what circuit would be left? What would be the value of the volage Vx? What would happen to the current dependent source? Explain your reasoning.
Kindly give neat and clean exlanation Calculate the power dissipated by the voltmeter and by resistor R given figure when (a) R = 250 ohm and (b) R = 2 Mohm. Assume that the voltmeter sensitivity (sometimes called the figure of merit) is 10 Kohm/V.
KCL and KVL, find I1, I2, & I3. Show complete illustration/solution
Q2. In the adjacent figure we have R2 = 7.9 kW, R3 = 1.45 kW, and e1 = 25 V, e2 = 10 V. a) ( If the ammeter shows the value +6 mA and the voltmeter shows the value +5.8 V, determine the value of the resistor R1. b) Determine the electric current I3. c) Determine the electric current I2 by two different methods. d) Evaluate Vad along two different paths. e)What would be the value of the voltage shown by the voltmeter if we connected its red wire to the positive pole of the power supply (electric current source) e2 and its black wire to the negative pole of the power supply e1?