Answered: Q.29: For the ideal transformer circuit…

Q.29: For the ideal transformer circuit shown, find the average power delivered to (1Q) resistor? (Ans.: P,=775.07W) 452 7.20 120V rms ideal

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4MCQ: An ideal transformer has no real or reactive power loss. (a) True (b) False

See similar textbooks

Related questions

Q: A Step-down transformer at Van Eck power station in Windhoek operates at V=10 kV on the primary side…

A: we need to find out the current, on secondary side of the transformer.

Q: Draw an HVDC system with proper arrangement of converters. Evaluate its technical and economic…

A: The electricity generated in a power station is transmitted over long distances to reach the…

Q: A single-phase, dry-type, general-purpose industrial distribution A transformer has the…

A: Given data, P=50 kVAf=60 HzVH=480 VVL=120 VZimpedance=3.80+j4.43 Ω%R=3.80 Ω%X=4.43 ΩPi=105 W

Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: In a transformer MMF remains same i.e, I1N1=I2N2 amd in auto transformer total current is the…

Q: 8. The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V,…

Q: Q.30: For the ideal transformer circuit shown, when V=16cos3t Volt, find the average power delivered…

A: Write the voltage source into phasor form,

Q: Upload answer sheets Find the following parameters of an ac voltage given by the equation…

A: Form Factor: It is the ratio of the RMS value to the average value. It is also known as root mean…

Q: 1. Peak to peak ripple is defined as a) The difference between average dc voltage and peak value b)…

A: 1. Peak to peak ripple is defined as The difference between the maximum ac and average dc voltages.…

Q: A drilling machine is driven by a single-phaseinduction machine connected to a 110-V rms…

A: The value of the supply voltage is 110 V. The current drawn by the drilling machine is 14 A. The…

Q: A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low…

Q: 630kVA 31500/400 DY 50Hz transformer has no load and short circuit tests power measurements are…

Q: Find the efficiency of a 150 kVA transformer at 25 % full load at 0.8 p.f. lag if the copper loss at…

Q: Consider a transformer with a primary coil consisting of 1226 turns and a secondary coil of 1078…

A: Number of turns on primary side, N1=1226. Number of turns on secondary side, N2=1078. The RMS…

Q: An ac generator provides emf to a resistive load in a remote factory over a two-cable transmission…

A: (a) Note- There is silly mistake in the (a) part of the Question, Question should be what is the…

Q: Compute the copper losses at full load if a 500KVA transformer has 90% efficiency at both half-load…

Q: 1) A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down…

Q: One side of a transformer has 1,800 turns while the other side has 450 turns. The high voltage side…

Q: 49). A distribution transformer is rated at 100 kVA. If the load p.f. is 0.707 lagging, the active…

A: Given a distribution transformer has, Rated kVA rating, S = 100 kVA Load power factor, cosϕ=0.707

Q: In an ideal transformer, the power in the secondary coil is 10 kW. The voltage of the primary is 500…

A: The given information for an ideal transformer is Power in secondary coil P2=10 kW. Voltage of…

Q: Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the…

Q: To a distribution transformer 8 residential consumers are connected. Each house connected load is 10…

A: Since in the given question, there is no mention of the demands or average demand or load factor, we…

Q: Illustrate the differences between tan δ terminology and power factor terminology (with the help of…

A: tanδ: If the applied electric field direction is reversed, the dipole alignment direction will be…

Q: 10- A 10-KVA, 500/250-V, single-phase transformer has its maximum efficiency of 94 % when delivering…

Q: A 15-kVA 8000/230-V distribution transformer has an impedance referred to the prima of 80+ j3000.…

A: a. The turns ratio of the transformer is determined as a=8000230=34.78 The load impedance referred…

Q: The nameplate of an electric molur owing information: Line voltage: 220V rms Line current: 15 A rms…

Q: An ideal transformer is rated to deliver 460 kVA at380 V to a customer, as shown in Figure.a. How…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Open-circuit test Short-circuit test Voc = 480 V Vsc = 10.0 V loc = 0.41 A Isc = 10.6 A %3D Poc = 38…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Neon signs (which often contain gases other than neon) use high voltage to excite gaseous atoms that…

Q: 1. a) Find the turns ratio N1/N2 for the ideal transformer in the circuitso that maximum average…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Q.4. Find the rms value of lo and VAB =? in the circuit shown below.

Q: A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the following parameters: R, = 1.5 a, X, =…

Q: A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low…

Q: Problem: Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 V rms…

A: The given circuit is a bridge rectifier and the required parameters can be calculated by using the…

Q: A single-phase aç veltage AC-AC voltage converter 120-V rms 60-Hz source. The load resistance is 15…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: balanced load (a) kVA supplied Gwalior by each Univ. 1991) Example 33.16. Two transformers connected…

A: open delta connection or V-V connection- Some of the features of open delta connection…

Q: A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 16 + j120…

Q: 1. Peak to peak ripple is defined as a) The difference between average dc voltage and peak value b)…

A: The solution is given below. The answer for question 4 is option d.

Q: Determine the efficiency of a 150 kVA transformer at 50% of full load and 0.8 power factor lagging…

Q: Q.29: For the ideal transformer circuit shown, find the 452 average power delivered to (1Q)…

A: for the ideal transformer circuit shown find the average power delivered to 1ohm resistor

Q: A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal…

Q: A simple power system is shown in this Fig. The generator (230 V, 20 kVA) is connected to an ideal…

A: In the given question the base values at the generator side is given i.e. 480V, 10KVA. so we can…

Q: a device has an average power rating of 1200W and deisgn to operate 250V rms line. detrmine the…

Q: A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 18 + j80…

Q: Q.29: For the ideal transformer circuit shown, find the 452 average power delivered to (1Q)…

Q: carrying? Ans. 10 45 percent 10.44 A 100-KVA transformer is at 80 percent of rated load at power…

Q: ine 201 j60 N Zine 480 0° V

A: None of the given OPTIONS is correct

Q: A single-phase ideal transformer is rated at 1OKVA, 240V/120V. Calculate the following: a. Rated…

Q: The impedance ZL in the circuit shown in Figure is adjusted for maximum average power transfer to…

A: (a) Remove the load impedance from the circuit and draw an equivalent circuit including the mutual…

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

Q.29: For the ideal transformer circuit shown, find the
average power delivered to (1Q) resistor?
(Ans.: P=775.07W)
452
7.20
4:1
120V
川
12
ideal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer has no real or reactive power loss. (a) True (b) False
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A 400-turns auto transformer, operating in the step-down mode with 25 percent tap supplies a 4.8 kVA, 0.85 lagging power factor load. The input to the transformer is 2400 V, 60 Hz. Neglect the small losses and leakage effects. What will be the apparent power(in kVA) conducted and transformed respectively?
A transformer with a 10:1 ratio and rated at 60kVA, 2200/220V, 60Hz is used to step down the voltage of a distribution system. The low tension voltage is to kept constant at 220V. (a) What load Impedance connected to the low-tension side will be loading the transformer fully at 0.8 power factor (lag) ? (b) What is the value of this impedance referred to the high tension side?
A Step-Down Transformer. A transformer connected to a 120 V (rms) ac line is to supply 12.0 V (rms) to a portable electronic device. The load resistance in the secondary is 5.00 Ω. (a) What should the ratio of primary to secondary turns of the transformer be? (b) What rms current must the secondary supply? (c) What average power is delivered to the load? (d) What resistance connected directly across the 120 V line would draw the same power as the transformer? Show that this is equal to 5.00 Ω times the square of the ratio of primary to secondary turns.