A single-phase ideal transformer is rated at 1OKVA, 240V/120V. Calculate the following: a. Rated current of each side b. If a load with impedance Z = 1.5 + j0. 8N is connected at the low voltage side, given the high voltage side voltage V, = 24020°V, find the voltage phasor on the low voltage side and current on each side. c. The complex power supplied from the source.

A single-phase ideal transformer is rated at 1OKVA, 240V/120V. Calculate the following: a. Rated current of each side b. If a load with impedance Z = 1.5 + j0. 8N is connected at the low voltage side, given the high voltage side voltage V, = 24020°V, find the voltage phasor on the low voltage side and current on each side. c. The complex power supplied from the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Similar questions

If the turn ratio of a step-down transformer is 10:1 and the series impedance (referred to the primary) of j50 ohm. If the no-load primary voltage is 230 kV (line-to-line), the secondary side is serving a Y-connected balance load of 1.5+ j0.25 ohms, the reactive power (per phase) absorbed by the load would be?
A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following:(a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.
In a three-phase step-down transformer with 150 kVA, 2080/208 V 60 Hz Y / Y connected R1 = 0.45 ohm, X1 = 2.2 ohm, R2 = 4.5 mohm, X2 = 22 mohm, Rc = 10 kohm, Xm = 8 kohms. When installed at 120 kVA, 90 kW back power factor, if the voltage at the load ends is at its nominal value, a) Primary side terminal voltage b) Yield (efficiency) c) Calculate the voltage regulation value?
1) A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following: (a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.
A Wye-Delta transformer is connected t0 66 kV input three-phase transmission line. Each transformer is rated at 1000 kVA and has step-down ratio of 8.1_ The bank supplies balance load having powel factor of hag with load current of 70 Assume idea transformer; determine_ The primary line and phase voltages The secondary line and phase voltages The secondary line and phase currents The apparent and active power at the load Total kVA capacity of the transformer
A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a three-phase Ynyn0 connected transformer. The equivalent impedance per reduced phase of the transformer to the primary is Zeq1= 1+j5 Ohm. The nominal primary voltage is V1Ln= 5920 V and the conversion ratio is a= 10. what is the amplitude of the actual voltage falling on one phase of the specified load? (simplified equivalent circuit will be used).
A 50 MVA, 11/132 kV three-phase, 50 Hz, generator transformer has guaranteed parameters as, load loss 160 kW at full load at 75°C, no load loss 30 kW and percentage reactance 9% at rated load. Calculate the following:*percentage regulation a full load and unity power factor*percentage regulation at 3/4 load and 0.85 lagging power factor*efficiency at full load and unity power factor*efficiency at 3/4 load and 0.85 lagging power factor(Use 5 decimal places)
A 500 kVA, 1100/400 V , Dy1 transformer takes 730 W on no-load and 3,1 kW on short circuit. The transformer supplies a balanced load of Z = 0,8 +j 0,6 ohm per phase connected in Delta. Calculate: a) The Power Factorb) Power and Reactive power of the Loadb) The transformer efficiency at this loadc) The equivalent transformer resistance in secondary terms.
A two-winding transformer rated at 100 kVA, is connected as an autotransformer to provide 10kV from a 15kV supply. Calculate the new rated kVA output. consider the power transformer mode and calculate the related currents Where, Vp = 10000VIp = S/(√3Vp) Is = S/(√3Vs) When find the new currents and voltages proceed to find the primary and secondary powers of the autotransformer. And conclude the rating of the autotransformer.
3) A 120 KVA three -phase transformer (three -phase power), 13200/480 V (line a line) in delta-strella connection has a resistance of 1.3% and a reactance of 8.2% per unit. a) Calculate the phase impedance of the transformer referred to the bass side voltage. b) Calculate the phase impedance of the transformer referred to the high side voltage. c) Calculate the efficiency of the transformer into nominal conditions and with F.P. 0.8 in delay. Three -phase loss in the nucleus is 1500 W.
Given a 115kV/13.2kV distribution transformer rated at 30 MVA (OA) with an 8% nameplate impedance (Per Unit Transformer Impedance), calculate: The Full Load current in amps The Short Circuit current in amps The FA rating in MVA The FOA ratings in MVA.
Determine the efficiency of three-phase 400 kVA, 11kV/ 380 V transformer at over-loadingcondition by 15% of its rated with unity power factor load. The copper and iron losses atfull load are 16 kW, 4 kW respectively.b) State one or more of the ways to reduce the losses that taken place in transformers.