Answered: Q.4: Use the mesh analysis on a circuit…

Q.4: Use the mesh analysis on a circuit at Figure 2 to find: a- Currents on resistors RL? b- Voltages at nodes A, and B? c- Power dissipated at RL? 22 12V 42 RL =42 Node A Node B 42 8V 6V Figure ?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

By measuring the currents and times and then draw the current vs time graph using the measurement at the lab for ε =8 V, R=1M Ω and C=4.7μF. When is the capasitor charged fully?
A constant current transfers 10*10^14 electrons onto one plate of a capacitor in 3 minutes [min]. (a) What is the current, in units of amperes [A]? Express the answer using an appropriate SI prefix such that there are only 1, 2, or 3 digits shown to the left of the decimal. (b) If the capacitor has a capacitance of microfarads [F], what is the voltage in units of volts [V] across the capacitor?
A student Mei who is doing the experiment measures a voltage V = 0.094954 V and a current I = 1.0747 A, then she uses equation (2) to calculate the resistance R. What value does Mei determine for R? equation(2) ?= ?/?
John went to electronic store to buy a 17.5 resistor for his project. However, the store only has 5 resistors. What minimum nuber of 5 resistor that he must by? How will he connect these resistors to come up with 17.5 ? He is expected to use all the resistors tht he will buy?
What is the voltage across the 10k resistor? What is its current? What is the current through the 4k and 6k resistors? What is the voltage across the 4k resistor? 6k resistor? What is the sum of the voltages across the 4k and 6k resistors? What is the Req of the circuit? What is the current of the 10V source?
Q4/ Use Super Position theorem to find the current flowing through Resistance(Rf) and also voltage across that resistor. Rd=25 Re=6 Rf=4 Vm =15 Vn = 16
Please help: Pacemakers designed for long-term use commonly employ a lithium-iodide battery capable of supplying 0.42 A•h of charge (A) How many coulombs of charge can such a battery supply? Express your answer using two significant figures (B) If the average current produced by the pacemaker is 5.6 micro Amps, what is the expected lifetime of the device? Express answer using two significant figures
links:https://www.youtube.com/watch?v=ty9QSiVC2g0 https://www.youtube.com/watch?v=n5bKzBZ7XuM
Calculating the Cost Effectiveness of Compact Fluorescent Lights (CFL)If the cost of electricity in your area is 12 cents per kWh, what is the total cost (capital plus operation) of using a 60-W incandescent bulb for 1000 hours (the lifetime of that bulb) if the bulb cost 25 cents? (b) If we replace this bulb with a compact fluorescent light that provides the same light output, but at one-quarter the wattage, and which costs $1.50 but lasts 10 times longer (10,000 hours), what will that total cost be?
What similarities can you draw between the formulas of finding the capacitance and resistance in series and parallel circuits? Aside from P=IV, what other ways can we obtain power using Ohm's Law?
John went to the electronic store to buy a 17.5 Ω ???????? for his project. However, the store only has 5 Ω resistors. What is the minimum number of 5 Ω resistors that he must buy? How will he connect these resistors to come up with 17.5 Ω? He is expected to use all the resistors that he will buy?
Answer the following 1. A voltage of 120V generates an IR drop across two resistors connected in series. If the voltage drop across R1 is 30V, what is the voltage drop across R2, in Volts? a) 80 b) 40 c) 100 d) 90 2. Three resistors R1, R2 and R3 of 20, 40 and 60 ohms are connected in parallel through the 120 V power line. What is the total current in the power line? a) 10A b) 12A c) 11A d) 15A 3. Resistors in a circuit are generally used to: a) increase the flow of the current b) decrease the flow of current c) avoid overvoltage d) decrease the power in the circuit