Q1/ A hydraulic oil ISO 68 is flowing by velocity 20 ft/sec through a hydraulic line at a volume flow rate of 250 GPS (g/sec). Find the pressure drop in bar unit for a hose volume of 70 m³. Note: Oil ISO 68 density is 54.9 lb/ft³ or 880 Kg/m³ and a kinematic viscosity of 68 cSt At 104°F. ( Use IS unit )

Q1/ A hydraulic oil ISO 68 is flowing by velocity 20 ft/sec through a hydraulic line at a volume flow rate of 250 GPS (g/sec). Find the pressure drop in bar unit for a hose volume of 70 m³. Note: Oil ISO 68 density is 54.9 lb/ft³ or 880 Kg/m³ and a kinematic viscosity of 68 cSt At 104°F. ( Use IS unit )

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed. Choose the right answer below: a.16.3 m/s b.18. 3 m/s c.17. 3 m/s d.19. 3 m/s
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?
Calculate pressure loss in a pipe ( d = 55 mm, L = 200 m ), for oil mass flow rate of 133 kg/min. Oil density is 900 kg/m3and kinematic viscosity is ν = 4·10-5 m2/s. The sum of local losses in the pipe is 3,5. Round off the answer to one decimal digit in kPa, but enter the answer without the unit.
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed. a.19. 3 m/s b.18. 3 m/s c.16.3 m/s d.17. 3 m/s PLEASE INCLUDE FIGURE OR FBD
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed. a. 18. 3 m/s b. 17. 3 m/s c. 19. 3 m/s d. 16.3 m/s With FBD
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed. (WITH FREE BODY DIAGRAM) CHOICES: a.17. 3 m/s b.18. 3 m/s c.19. 3 m/s d.16.3 m/s
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed. a.18. 3 m/s b.16.3 m/s c.17. 3 m/s d.19. 3 m/s
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
The pressure drop in a venturi meter (Fig. P3.128) varies onlywith the fluid density, pipe approach velocity, and diameterratio of the meter. A model venturi meter tested in water at20 ° C shows a 5-kPa drop when the approach velocity is 4 m/s.A geometrically similar prototype meter is used to measuregasoline at 20 °C and a flow rate of 9 m 3 /min. If the prototypepressure gage is most accurate at 15 kPa, what should theupstream pipe diameter be?
Gasoline specific mass: 0,82 g/cm3Diameter 1 = 150mmDiameter 2 = 100mmCalculate the volumetric flow rate through a pipe, considering the results in:a) Bourdon Tubeb) Differential Manometers
In a chemistry plant, through a horizontal smooth pipeline with a diameter of 0,3 m, a fluid with density and viscosity of 769 kg/m3 and 0,0007 Pa-s, respectively is flowing with a flow rate of 0,009 m3/s. Disregarding the pipe entrance effects and treating flow being steady, uniform and incompressible; a) Find the magnitude of mean velocity (in m/s). (Please use only 3 decimal digits.) b) Find Reynolds number. (Please do not use any decimal digit.) c) Find the magnitude of friction factor. (Please use 4 decimal digits.)