Q1 Answer by True or False the following statement1- Kirchhoff's current law states that the current flowing into a node (or a junction)must be equal to the current flowing out of it.2- A 20-ohm and 80-ohm resistor are connected in parallel across a 64-volt battery.The total current for this circuit is 4 amperes.3- A junction where two (or) more than two network elements meet is known as anode4- The algebraic sum of voltages around any closed path in a network is equal toone5- The basic laws for analyzing an electric circuit are Newtons laws6- Relation between currents according to KCL for a node with two input current(Ii & 12 )and two outputs (I3 & L4) is I-12+ls+1-07- A 3-ohm and 6-ohm resistor are connected in parallel, and a 10-ohm resistor isin series with the combination. When 36 volts is applied to the three resistors,the total current in the circuit is 2 amps.8- KCL and KVL is limited to write two equations for a particular circuit.9- When assigning branch currents, you need not be concemed with the directionyou choose.10- For the circuit shown below (Fig.1) the value of resistance is 17.5 ohms5 ohm2 A70 v7 ohmR?Fig.1

1.TRUE According to Kirchhoffs sum of current law current flowing into a node must be equal to the…

Q1 Answer by True or False the following statement 1- Kirchhoff's current law states that the current flowing into a node (or a junction) must be equal to the current flowing out of it. 2- A 20-ohm and 80-ohm resistor are connected in parallel across a 64-volt battery. The total current for this circuit is 4 amperes. 3- A junction where two (or) more than two network elements meet is known as a node 4- The algebraic sum of voltages around any closed path in a network is equal to one 5- The basic laws for analyzing an electric circuit are Newtons laws

Q1 Answer by True or False the following statement 1- Kirchhoff's current law states that the current flowing into a node (or a junction) must be equal to the current flowing out of it. 2- A 20-ohm and 80-ohm resistor are connected in parallel across a 64-volt battery. The total current for this circuit is 4 amperes. 3- A junction where two (or) more than two network elements meet is known as a node 4- The algebraic sum of voltages around any closed path in a network is equal to one 5- The basic laws for analyzing an electric circuit are Newtons laws

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Resistors, 10 ohms and 15 ohms, are connected in series. The power being consumed by the 10-ohm resistor is 22.5 watts. Determine the following: the value of the voltage source energizing the circuit; the power being dissipated by the 15-ohm resistor if the two resistors were to be connected in parallel using the same source; NOTE Use the appropriate unit of measurement; observe the best applicable engineering notation and Greek prefix. Wrong unit of measurement will make the final answer wrong. Box your final answers. Express your answers accurate to four decimal places.
Consider three electrical loads of equal resistance 30 Ohms connected in parallel to an electrical socket in a Canadian home (120 V, 60 Hz). Assume that the maximum current that can be delivered to the circuit before tripping is 20 A. What will happen if you attempt to connect a fourth load of resistance 24 Ohms in parallel to this circuit? Question 12 options: There is not enough information to answer this problem. The current will not exceed 20 A and the circuit will not trip. The current through the circuit is unchanged when adding the fourth load. The current will exceed 20 A and the circuit will trip.
If they are defined as Vs=2V and Is=12A, respectively, in the circuit given below, how many volts will the Vx node voltage be? TIP: You might consider solving it with the Node Method. NOTE: Please enter your answer as 1 digit after the comma. Help me please... Thank you so much.
With switch SW1 closed and switch SW2 open, complete the following using the values from the table:i. Determine the total resistance in the circuit. ii. Determine the currents flowing in the circuit. iii. Determine the volt drops around the circuit. iv. Use the appropriate Kirchhoff’s law to confirm your results.
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
Consider three electrical loads of equal resistance 30 Ohms connected in parallel to an electrical socket in a Canadian home (120 V, 60 Hz). Assume that the maximum current that can be delivered to the circuit before tripping is 20 A. What will happen if you attempt to connect a fourth load of resistance 24 Ohms in parallel to this circuit? Question 3 options: The current will exceed 20 A and the circuit will trip. The current through the circuit is unchanged when adding the fourth load. There is not enough information to answer this problem. The current will not exceed 20 A and the circuit will not trip.
Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C what is the answer? VD?
Three resistors of 50 ohms, 100 ohms, and an unknown resistance R are connected in parallel and the combination is connected to a 25-V source. If the total current delivered by the source of 1 A, determine the current in amperes in the 50-ohm resistor. NOTE Express your final answers accurate to four decimal places; avoid rounding off intermediate values in the solutions to avoid deviation due to rounding-off within the solution. USE ENG NOTATION
A transmission line is being built to bring power to a remote community, which is 40 miles from the nearest substation. The conductor has a resistance of 20 ohms. The community requires 100 MW of power at a voltage of 110 kV. What does the voltage leaving the substation need to be to account for voltage drop over the line, and what is the power loss over the transmission line? Please show your work!
2- Please I want answer of this Electrical Principles question. Thanks
Answer the ff: 1. What are Voltage, Amperage, and resistance? 2. What is the difference between power and energy? 3. What is the difference between series and parallel circuits? 4. Determine the current flow in a circuit with a resistance of 5 Ohms on a 120 and 240 Volts current supply. (Circuit refers to the electrical wiring installation). 5. A circuit has a resistance of 20 Ohms, and the current flows at 12 Amperes. Determine the Voltage. 6. A water heater draws 10 Amperes at 240 Volts current supply. Determine its heat resistance.
Complete Solutions 1. A 12-ohm resistor is connected in parallel with a series combination of 8-ohmand 16-ohm resistors. If the voltage across the 8-ohm resistor is 48-volts,calculate the (a) total resistance, (b) total supply voltage, and (c) circuit current.2. A 45-ohm resistor is connected in series with a resistor R whose ohmic value isunknown. If the total current (taken by both resistors) is 7-amperes and thesupply voltage is 120-volts. Calculate the resistance R of the unknown.