Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular plate of size 0.75m x 0.55 m and an inclined plane with angle of inclination 45" as shown in figure 1. The weight of the rectangular plate is 0.5 kN and it slides down the inclined plane with a uniform velocity of 0.35 m/s. The thickness of oil film is 1.75 mm. Then, state the scope for this obtained viscosity? Recbanglar plabe -oil Inclined plane Figure 1

Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular plate of size 0.75m x 0.55 m and an inclined plane with angle of inclination 45" as shown in figure 1. The weight of the rectangular plate is 0.5 kN and it slides down the inclined plane with a uniform velocity of 0.35 m/s. The thickness of oil film is 1.75 mm. Then, state the scope for this obtained viscosity? Recbanglar plabe -oil Inclined plane Figure 1

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter8: Time And Time-related Variables In Engineering

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
Using the information given in Table 10.4, determine the ratio of local pressure and density to sea-level values. Estimate the value of air density at the cruising altitude of most commercial airliners. Altitude (m) sealevel PPsealevel 0 (sea level) 1000 3000 5000 8000 10,000 12,000 14,000 15,000
A cylindrical piston of weight 5N slides in a lubricated pipe as shown in figure.The clearance between the piston and the pipe is 0.025 mm. If the piston decelerates at0.5 m/s2 when the speed is 5 m/s, what is the viscosity of the oil ?
Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow will be laminar or turbulent assuming that the dynamic viscosity of water is taken as1.30 × 10−3 kg/ms and its mass density as 1000 kg/m3. If oil of specific gravity 0.9 and dynamic viscosity 9.6 × 10−2 kg/ms is pumped through the same pipe, what type of flow will occur?
1.) What is the mass (lbm) of an object that has a base area of 4 inch2 which exerts a pressure of 25 psi? 2.) Determine the dynamic viscosity (Pa-sec) and kinematic viscosity (m2/s) of water with a specific weight of 9.81 kN/m3, if a Falling Sphere Viscosimeter test is conducted using an aluminum sphere that has a diameter of 10 mm and a specific weight of 28.06 kN/m3. The theoretical terminal velocity of the sphere is 0.650 m/s. Round off your answer to 3 decimal places. 3.) Given the water tank A in an orifice setup that transfers water to tank B, determine the theoretical and actual velocity and flow rate if the time it takes to fill up tank B is 20 sec. 4.) Given the computed velocities and flow rates in Question 3, determine the coefficient of contraction, velocity, and discharge. Assume the diameter of vena contracta to be 4mmø.
A block in the following figure is pulled up with a Force 20 +S Nt. The weight of the block is 10 Nt. The area of the contact surface between the block and fluid is 10 cm2. a)find the velocity of the block if the fluid is an ideal fluid b)find the velocity of the block if dynamic viscosity of the Fluid between the block and inclined surface in the figure is 0.2 Nt.s/m2. (S=4)
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined in an internal reservoir inside the closed tank, the height of mercury is 450mm. An open manometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , the deflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y. b) Pressure @ point B in kPa. c) Pressure @ point C in psi.
) Consider a double - fluid manometer attached to an air pipe shown in Figure. If the specific gravity of one fluid is 13.55, determine the specific gravity of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be 100 kPa. (
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?