Q1/ During a sudden accidental in a gas station, Gasoline from a fuel tanker completely fills an 18-in.-diameter, smooth, concrete sewer. If the flowrate is 10 ft'/s, determine the pressure drop in a 100-ft horizontal section of the pipe. Repeat the problem if there is a 2-ft change in elevation of the pipe per 100 ft of its length.

Q1/ During a sudden accidental in a gas station, Gasoline from a fuel tanker completely fills an 18-in.-diameter, smooth, concrete sewer. If the flowrate is 10 ft'/s, determine the pressure drop in a 100-ft horizontal section of the pipe. Repeat the problem if there is a 2-ft change in elevation of the pipe per 100 ft of its length.

Name: Q1/ During a sudden accidental in a gas station, Gasoline from a fuel
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q1/ During a sudden accidental in a gas station, Gasoline from a fuel tankercompletely fills an 18-in.-diameter, smooth, concrete sewer.If the flowrate is 10 ft/s, determine the pressure drop in a 100-ft horizontal sectionof the pipe. Repeat the pro

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. UNKNOWN: DIAMETER OF THE PIPE STRICTLY SHOW COMPLETE FBD AND SOLUTION MUST BE HANDWRITTEN
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
For the pipe system shown. Assume n = 0.013 for all pipes. Neglect minor losses. 1. Compute the head loss from A to B in terms of Q. a. 0.056Q2 b. 0.029Q2 c. 0.016Q2 d. 0.096Q2 2. Assuming Q = 12 cfs, compute the head loss of pipe CD. a. 15.78 ft b. 13.02 ft c. 18.56 ft d. 24.56 ft 3. Assuming Q = 12 cfs, compute the total head loss from A to D. a. 47.786 ft b. 56.673 ft c. 89.451 ft d. 32.562 ft
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (∊ = 0.00061 m). Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flow through the pipe, what must be the pressure at A?
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
PROBLEM 1: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses.
PROBLEM 2: Water flows downwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses.
1A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the meter is 100 mm and the pressure at the throat is 400 mm of mercury below the atmosphere. If 3% of the differential pressure is lost between the inlet and the throat, determine the flow rate of the pipeline. Can you draw the figure and complete solution:
Water flows from a pressurized tank, through a pipe of diameter D, exits from a nozzle of diameter d, and rises a height H above the tank bottom. The water depth in the tank is h. Determine the relationship between the gage pressure of the in the tank and H. If the gage reads 10 psi, d = 2 in, D = 4 in, and h = 3 ft, calculate the jet height H.
Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft.If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.