10. Two galvanized iron pipes of diameter D are connected to a large water reservoir as shown. Pipe A has length L and pipe B has length 2L. Both pipes discharge to atmosphere. Which pipe will pass larger flow rates? Justify (without calculating the flow rate in each pipe). Compute the flow rates if H=10 m, D=50 mm, and L=61 m. D Pipe A, length: L Pipe B length: 2L

10. Two galvanized iron pipes of diameter D are connected to a large water reservoir as shown. Pipe A has length L and pipe B has length 2L. Both pipes discharge to atmosphere. Which pipe will pass larger flow rates? Justify (without calculating the flow rate in each pipe). Compute the flow rates if H=10 m, D=50 mm, and L=61 m. D Pipe A, length: L Pipe B length: 2L

Name: 10. Two galvanized iron pipes of diameter D are connected to a large
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 10. Two galvanized iron pipes of diameter D are connected to a large water reservoir as shown.Pipe A has length L and pipe B has length 2L. Both pipes discharge to atmosphere. Which pipewill pass larger flow rates? Justify (without calculating the f

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the hydraulic radius of a pipe with a diameter of 12mm is
Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline (SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C.
On a circular conduit there are different diameters: diameter D1 = 2 m, changes into D2 = 3 m. The velocity in the entrance profile was measured: v1 = 3 m/s. Calculate the discharge and mean velocity at the outlet profile (see figure below). Determine also type of flow in both conduit profiles (whether the flow is laminar or turbulent) – temperature of water T = 12° C. (use Reynold’s number Re), For laminar flow: Re<2320, For turbulent flow Re>2320, Kinematic viscosity of water of 12°C, v is equal to 1,24 10^-6 m2/s.
An air-conditioning system is designed to have a ductwith a rectangular cross section 1 ft by 2 ft, as shown. Duringconstruction, a truck driver backed into the duct and made it atrapezoidal section, as shown. The contractor, behind schedule,installed it anyway. For the same pressure drop along the pipe,what will be the ratio of the velocity in the trapezoidal duct tothat in the rectangular duct? Assume the Darcy-Weisbach resistance coefficient is the same for both ducts.
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
An unfinished-concrete 6-ft-diameter sewer pipe flows halffull. What is the appropriate slope to deliver 50,000 gal/minof water in uniform flow?
Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft.If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.
A machined entrance cone venture tube that has been fabricated according to ASME standards is fit to a 7 cm ID water pipe. The minimum diameter is 4 cm. If the pressure drop across the venture is 19 kPa, calculate the water flow rate.
A 5 cm diameter potable water line is to be run through a maintenance room in a commercial building. Three possible layouts for the galvanized iron water line are proposed as shown in the figure. The bends are conventional threaded fittings. Select the option that minimizes losses and determine the pressure drop for a flow of 350 L/min. For the elbo losses use, hℓm =
Benzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter per second.
Considering pipe loss only, how much head is required to deliver 0.222 m³/s of heavy fuel oil at 38°C through 914 m of new cast iron pipe, 300 mm inside diameter? Use ε=0.00024 m. (ANSWER MUST BE = 41 m)
For the flow of 12.9 L/min of water at 75 degrees Celcius in a plastic pipe, 16mm OD x 1.5mm wall, compute the expected maximum velocity of flow. Answer is 1.95m/s. Please show how to solve.