Q1: For a single-phase full bridge-controlled rectifier. The input supply voltage 220 V, 50 Hz, the firing angle (a-45°), and the load is (R=10 2). Draw the rectifier circuit diagram and then find the following: a. draw to scale VLOad- and ILoad b. comment how the SCR can be turned off? c. Find Vdc and Vms for the load voltage.

Q1: For a single-phase full bridge-controlled rectifier. The input supply voltage 220 V, 50 Hz, the firing angle (a-45°), and the load is (R=10 2). Draw the rectifier circuit diagram and then find the following: a. draw to scale VLOad- and ILoad b. comment how the SCR can be turned off? c. Find Vdc and Vms for the load voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 4. The value of dc current (Idc) in amperes is ? 5. The value of the output peak voltage (Vpout) in volts is ? 6. The value of peak secondary voltage (Vpsec) in volts is ? 7. The value of primary peak voltage is (Vppri) in volts is ?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is ? 2. The value of the dc voltage (Vdc) in volts is ? 3. The value of the ripple factor is ?
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 5 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage.
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 18 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1100 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is..... 2. The value of the dc voltage (Vdc) in volts is..... 3. The value of the ripple factor is..... 4. The value of dc current (ldc) in amperes is..... 5. The value of the output peak voltage (Vpout) in volts is..... 6. The value of peak secondary voltage (Vpsec) in volts is..... 7. The value of primary peak voltage is (Vppri) in volts is.....
A 2500-V, 2-A, dc power supply is to be designed with a ripple voltage ≤ 0.5 percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b) What is the minimum PIV rating for the diode? (c) What is the rms value of the transformer voltage needed for the rectiﬁer? (d) What is the peak value of the repetitive current in the diode? (e) What is the surge current at t =0+?
A 3.3-V, 30-A dc power supply is to be designed with a ripple of less than1.5percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b)What is the PIV rating for the diode? (c)What is the rms value of the transformer voltage needed for the rectiﬁer?(d) What is the value of the peak repetitive diode current in the diode? (e) What is the surge current at t =0+?
The voltage waveforms shown below are obtained from a three-phase power rectifier used in an ESKOM application.The rectifier output before the inductive filter is denoted by VL and the load voltage after the inductive filter by Vo. Ignore any diode losses and consider a load resistance of 12.7 Ω. Analyse the waveforms and specify / calculate,11) the supply frequency;12) the rectifier pulse number;13) the rectifier average output voltage;14) the average output current;15) the r.m.s. value of the output current;16) the r.m.s. value of the harmonics present in the output current;17) the dc current rating of the rectifier diodes;18) the r.m.s. current rating of the rectifier diodes;19) the peak repetitive reverse voltage rating of the rectifier diodes;20) the peak repetitive forward current rating of the rectifier diodes;21) the line-line r.m.s. voltage of the three-phase supply;22) the rectification efficiency of the converter;23) the converter transformer utilisation factor;
What is mean by phase angle control method?. Differentiate Natural and forced commutation method. Is it possible to construct rectifier circuits by MOSFET? Justify. ( short anser only plases )
2) Design a Regulated DC Power supply circuit in multisim of 5V for charging a mobilephone? Note: use bridge rectifier, ac voltage source 120 Vrms or 230 Vrms for the design and appropriate capacitors and voltage regulators to get output exactly at 5V.
A particular load has to be supplied with an average power of 50mW, 5V dc voltage. Find the value of capacitance and transformer turns ratio in a half wave rectifier with capacitor filter such that the ripple factor should not exceed 1%. Assume 220V rms, 50Hz supply voltage. Also, sketch the voltage waveform across the load.
Design a circuit for an uncontrolled half-wave Rectifier based transformer step down containing a capacitor filter circuit, with writing the laws of the circuit and the shape of the output wave, with a comparison between the current output wave and the voltage output wave in terms of being affected by the placement of the filter.
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous