Q1: Shaft subjected to the loadings in phase shown such that: T=0 N.m to 200 N.m M=-200 to 200 N.m The shaft has d1=60 mm, d2=40mm, r=8 mm, cold drawn, operating temp. 550 C, relaibility of the data 99.9%, Material Properties; out = 1260 MPa, Out=813 Mpa. Is the shaft fails for infinity life design? T м M d T

Q1: Shaft subjected to the loadings in phase shown such that: T=0 N.m to 200 N.m M=-200 to 200 N.m The shaft has d1=60 mm, d2=40mm, r=8 mm, cold drawn, operating temp. 550 C, relaibility of the data 99.9%, Material Properties; out = 1260 MPa, Out=813 Mpa. Is the shaft fails for infinity life design? T м M d T

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part A For a hard aluminum notched part having notch dimension r = 0.75 in, geometric stress-concentration factor Kt = 2.8, material strength Sut = 50 kpsi, and bending loading type, find the Neuber factor, a (in inches). Part B Find the material's notch sensitivity, q. Part C Find the fatigue stress-concentration factor. Kf.
A hallow steel shaft transmit 600km at 500 rpm.the minimum
The values given for a radial plain bearing are:Shaft diameter = 40 mm, bearing width = 30 mm, Pem = 6 N / mm2, Radial force = 2 KN, Ty = 45 C, oil: ISO VG 15, bearing clearance = 35 µm, dynamic viscosity for given oil and temperature = 12 m Pa. sRequired:a) What is the working cycle of the shaft?b) Find the Sommerfeld number.
Data:P = 2 kipd = 3.6 inchw = 305 millimeterst = 0.03 meterr = 5.08 centimeterh = 0.6667 feet a) Calculate the maximum static stress in the material (in MPa). b) Estimate the theoretical stress concentration factor at the fillet c) Estimate the theoretical stress concentration factor at the hole
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
Please solve clearly step by step otherwise don't attempt.will report. A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the mean torque. The shear stress in the shaft should not exceed 46 MPa and the twist 1.2° per metre length. Determine the diameter required if, (i) The shaft is solid
What reversing torque in N-mm, can a 38 mm shaft sustain if the yield strength and endurance strength is 244.14 MPa and 143.5 MPa respectively? Assume a factor of safety of 2.
5. A 50 mm diameter shaft is made from carbon steel having ultimate tensile strength of 630 MPa. It is subjected to a torque which fluctuates between 2000 N-m to – 800 N-m. Using Soderberg method, calculate the factor of safety. Assume suitable values for any other data needed.
A torque of 40,000 N.m is applied to a 10 cm diameter shaft. What is the factor of safety of a steel(Sy = 410 MPa) if its shear strength is one-half of its capacity in tension?
Read and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : Recall that for spings the Zimmerli point on the modified Goodman diagram is located at (Ssm, Ssa) = (55, 35) ksi. Suppose that a particular spring wire has a shear ultimate strength of Ssu = 89 ksi. Determine the shear endurance limit of the spring wire. Give your answer in units of ksi,
A flange coupling connects two 2” diameter shafts. The flanges are fitted with 6 bolts of SAE 1040 steel on a 7” bolt circle. The shafts runs at 300 rpm and transmits 45 hp. Assume a factor of safety of 5, ultimate tension of 70,000 psi, and ultimate shear of 55,000 psi. Determine: a) The torque transmitted, in-lbs b) The force applied per bolt, lbs c) The diameter of the bolt required, in d) The thickness of flanged to be used, in
9. A 2Hp motor rotates at 1500 rpm. If the allowable torsional stress is not to exceed 40 MPa, what is the minimum diameter of shaft?