Q1: The crank ABCD shown, F=1 kN. The rod is made from wrought-aluminum alloy 2024 heat treated and the fillet radius at the wall is r=4 mm. Consider the transverse shear effect. Find the factor of safety of this crank. 200 mm D35 mm 25-mm-dia. round rod bent into crank 250 mm -100 mm F Fig. 1

Q1: The crank ABCD shown, F=1 kN. The rod is made from wrought-aluminum alloy 2024 heat treated and the fillet radius at the wall is r=4 mm. Consider the transverse shear effect. Find the factor of safety of this crank. 200 mm D35 mm 25-mm-dia. round rod bent into crank 250 mm -100 mm F Fig. 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.2P: A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The...

See similar textbooks

Related questions

Q: he shaft, shown below, consists of rods AB and CD and a tubular segment BC. The rods are onnected…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing…

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or tensile or…

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: = 8 kN, T12 = 2 kN, T

Q: PROBLEM 1 Diameter of pin at A = 25 mm Diamcter of cable BC = 10 mm Ultimate shear stress of pin =…

A: Given: dA=25 mmdBC=10 mmτmax=120 MPaσcable=1250 MPa

Q: The assembly consists of three disks A, B, and C that are used to support the load of P. The load P…

A: Given data:

Q: os. A mild steel strut is of single angle section 100 mm x 75 mm x 8 mm. Its length is 3m with both…

A: Strut is a member or bar (in any position), which is subjected to axial compressive load. Column is…

Q: The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable…

Q: Two vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m.…

Q: The solid steel rod (1) has an allowable shear stress of 17 ksi. The brass tube (2) has an allowable…

A: given; allowable shear stress for rod (τ)=17ksi…

Q: The rigid bar of negligible weight is pinned at o and attached to two vertical rods. Assuming that…

Q: Two rods are connected to each other and are restrained at top and bottom. The top portion is steel…

Q: F SIMPLE STRESSES 2. Based on Problem No. 1, determine the shear stress in the grain of the timber…

A: As per honor code and answering guidelines I can answer 1st question at a time.If you want other…

Q: The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. 6ft AAn = 1 in Agg = 2…

Q: A mild steel strut is of single angle section 100 mm x 75 mm x 8 mm. Its length is 3m wiun both ends…

A: Stress When body is subjected to a load then body will get deform but body will resist the…

Q: The hanger at B is held by 10 nails against a column. Determine (a) the shear force, V (in N)and (b)…

Q: The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α=…

Q: A bar is machined from steel and subjected to a static load of 5000 N. Assume the stress…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: The largest torque that can be applied safely at the upper end of the steel rod: Tmax = 319.07 lb•in

Q: A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a…

A: The flange thickness is 20 mm. Hence, option (B) is correct.

Q: The axial assembly consists of a solid 1.03-in.-diameter aluminum alloy [E = 9700 ksi, v = 0.24, a =…

Q: 25mm P. 500 mm Data Given Let steel tube denoted as 1 and brass rod denoted as 2 d10= 40mm E1 =…

Q: The compound bar has an assembly shown. • AB is steel (E, = 200 GPa, a, = 11.7 x 10 6 / °C) • BC is…

Q: Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and…

A: Given: Straight bar ABCD, Length of Parts AB, BC, CD = 500 mm

Q: Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

A: EA1= 73*109pa Let AB is part 1 and BC is part 2 Considering factor of safety 1.5 load acting is…

Q: Determine the diameter of a taper pin for use to fix a lever to a shaft, if it is to transmit a…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system P = 9 kips Q = 5 kips R = 20 kips S = 30 kips stress limit in (1) = 19 ksi…

Q: Two steel springs are arranged in series as shown. The upper spring has 24 furns of 50-mm- diameter…

A: The following details are given: For spring 1 n=24 turnsd=50mmR=186mm For spring 2…

Q: The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal before the Load P is…

Q: 8 in 5in 12 in S

Q: A rigid component ABC is supported by a pin-connected member (1). The member has a rectangular…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8…

Q: span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from…

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

Q: A locomotive semi-elliptical laminated spring has an overall length of 1.3 m and sustains a load of…

A: As per given question Length =1.3m Load=78kn No of leaves=2 Pressure =455N/mm2 E=210kn/mm2 We have…

Q: For the hollow shaft shown, the strength is 150 MPa. Determine 1. The internal reactions due to…

Q: Two solid steel wall supported shafts are connected using the 4 bolt flange. A torque is applied to…

A: Shear stress in the bolts needs to be calculated

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

Q: Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12…

A: Given Data The diameter of the vertical steel wire is: 0.05 in The length of the vertical steel wire…

Q: 7. A shaft made of mild steel is required to transmit 100 kW at 300 r.p.m. The supported length of…

A: We have to determine diameters of the shaft

Q: Rigid member AD is pin supported at D (single shear) and braced by pin connected rod BC (B and C in…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: given; diameter of steel(d1)=0.500inallowable shear stress of steel(τs)=13ksimaximum torque…

Q: Example 4: The 2014-T6 aluminum strut is fixed between the two walls at A and B. If it has a 2 in by…

A: Let us draw the free body diagram of the shaft, From the table, we can find the relation of the…

Q: Construct the buckling curve, P/A versus L/r, for a column that has a bilinear stress–strain curve…

A: Given: To draw P/A vs L/r for the above

Q: 1. Fluctuating loads can cause a tensile mean stress when a. 0<R<1.0 c. 0<R<-1.0 d. both a andb b.…

A: 1. Fluctuating Loads can cause a tensile mean stress when 0 < R < 1.0 Since the average…

Q: B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods…

A: Solution: A=30 mm2E=200 GPaα=15×10-6/°C∆T=60°C

Q: A rigid bar, pinned at O, is supported by a steel spring at A and a bronze spring at C. The steel…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Q1: The crank ABCD shown, F=1 kN. The rod is made from wrought-aluminum alloy 2024 heat
treated and the fillet radius at the wall is r=4 mm. Consider the transverse shear effect. Find
the factor of safety of this crank.
rd mm
200 mm
De35 mm
25-mm-dia. round
rod bent into crank
250 mm
-100 mm
Fig. 1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
What is the maximum possible value of the clamping Force C in the jaws of the pliers shown in the figure if the ultimate shear stress in the 5-mm diameter pin is 340 MPa? What is the maximum permissible value of the applied load P to maintain a factor of safety of 3.0 with respect to failure of the pin?
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A crank arm consists of a solid segment of length bxand diameter rf, a segment of length bltand a segment of length byas shown in the figure. Two loads P act as shown: one parallel to — vand another parallel to —y. Each load P equals 1.2 kN. The crankshaft dimensions are A] = 75 mm, fr> = 125 mm, and b3= 35 mm. The diameter of the upper shaft isd = 22 mm, (a) Determine the maximum tensile, compressive, and shear stresses at point A, which is located on the surface of the shaft at the z axis. (b) Determine the maximum tensile, compressive, and shear stresses at point B, which is located on the surface of the shaft at the y axis
A damper square mat is supporting a dead load weight of8 kN. Helical springs will be used to support the loadlocated at all corners with shearing stress of 120.6 Mpaat 20 turns. The spring has a deformation of 98.7 mmwith a mean radius of 80 mm. Design the minimumdiameter of the wire to support a load. Use G = 83 Gpa.
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
A semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.