Q1. An open belt drive configuration having 10 pulleys in total, the input and output speeds are 20 & 100 rpm respectively. Find the diameter of the last driver pulley if the corresponding diameters of the drivers are 12. 14, 16 and 18 meters while for the followers are 2, 4, 6, 8 and 10 meters? 0.6 m 2 m 3.2 m O 0.4 m O 4 m O 6.2 m O 2.2 m 6 m 8 m 10 m

Q1. An open belt drive configuration having 10 pulleys in total, the input and output speeds are 20 & 100 rpm respectively. Find the diameter of the last driver pulley if the corresponding diameters of the drivers are 12. 14, 16 and 18 meters while for the followers are 2, 4, 6, 8 and 10 meters? 0.6 m 2 m 3.2 m O 0.4 m O 4 m O 6.2 m O 2.2 m 6 m 8 m 10 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
Mechanical Engineering In a lamellae clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
Problem Solving. Solve the following problems completely. 5. Motors from two different manufacturers are being considered for application.Both motors are 50Hp, 460 volts, 3 phase, 60 cycles. Motor A operates at 80%efficiency and motor B operates at 89% efficiency. The expected need for themotor is 15 years. Motor A cost P120, 000.00 and motor B P150, 000.00.Electrical energy cost P8.00 per Kw-Hr and the motors will be operating 8 hoursper day, 250 days a year. Assume taxes and insurance are 3% of first cost. Whichmotor should be purchased?
In a lamella clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
In a belt drive design, the angle of wrap correction factor C θ is a function of the angle of wrap of the belt on the small sheave. If in a design, the angle of wrap of the belt on the small sheave is 1500 , then C θ = ________ 0 .
With a driveshaft turning at 2000 rpm , I then have a spring that can rotate a shaft 5000 rpm, I want this spring to assist in the drive of the driveshaft, how can I express that or calculate the effect of adding the spring would make. Including a spring system alongside a driveshaft that can assist the drive up to 5000rpm, how can I integrate the spring system to assist in the driveshaft drive, calculations on the change in rotation the spring would have of the driveshaft speed
The larger diameter and face of the disk of a multiple disk chutch are 225 mm and 20 mm respectively. The load applied to the spring of the clutch axially is 1500 N. Assuming that there are 8 pairs of friction 0.18 and tuning 800 rpm. Find the power transmitted by the clutch using uniform pressure method. (Ans, 13.67 kW)
A restaurant owner has decided to install a used fan that could deliver 18,000 CFM of air when running at 320 rpm. The fan is estimated to require at least 4.5 HP to deliver the volume of air needed. The owner has also a second hand motor rated at 5 HP and 1750 rpm. These data are all that the owner could provide you. He would like to use a standard chain and sprocket for the transmission. Use service factor = 1.1 and pitch = 0.5 inch.A) Determine the number of teeth and diameter of small sprocket. B) Determine the number of teeth and diameter of big sprocket. C) Determine the center distance and length of chain.
4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a reciprocatingpump, turning at 200 rpm. The system useschain#100 with smaller sprocket having 21 teeth.Assuming a service factor of 1.6 using C = D2 + D1/2,determine (a) the rated horse power of the chain, (b)number of teeth of the larger sprocket, (c) the pitchlength of the chain, and (d) the number of strandsrequired. Express your answer in 3 decimal place.
20. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the vehicle resumes moving. One way to do this is to “store” the energy in a spinning flywheel. One such design uses a solid disk flywheel with moment of inertia 0.040 kg m2 and maximum rotation rate 45000 rpm. (a) What is the maximum energy storage? (b) In principle it could store the kinetic energy of a 1700 kg car moving at what speed before braking? (c) If this energy is used to start the car moving again in 10.0 s, what is the power output of the system?
Question 04: Discuss the comparative study between chain and belt drives. How are they useful in the field of mechanical engineering, give some practical examples?
A v-belt drive is to transmit 330kW power from a pulley of 1m diameter running at 250rpm. The safe pull in each belt is 800N and the mass of the belt is 0.46kg per meter length. The angle of lap and the groove angle is 160º and 45ºrespectively. If the coefficient of friction between the belt and the pulley is 0.3. Calculate the number of belts required