Q:1. Answer following questions by considering your observations from your experiments. a. Explain what happen when the load on induction motor is increased 0 N.m to 1.2 N.m. ( Write down all necessary parameters which change in bullet form. Avoid unnecessary explanations). b. In case of synchronous generator how can we increase the voltage of generator? ( Write down all variables which increase the voltage of generator. Avoid unnecessary explanations)

Q:1. Answer following questions by considering your observations from your experiments. a. Explain what happen when the load on induction motor is increased 0 N.m to 1.2 N.m. ( Write down all necessary parameters which change in bullet form. Avoid unnecessary explanations). b. In case of synchronous generator how can we increase the voltage of generator? ( Write down all variables which increase the voltage of generator. Avoid unnecessary explanations)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.11P

See similar textbooks

Similar questions

For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal voltage of 10.45 kV. Determine (a) the voltage at bus 1, which is the generator bus, and (b) the generator and motor internal EMFs.
A 3 phase 4MVA, 12 kV star connected synchronous generator has Zs= 0.8+J30 ohm. Using circle diagram only, find: 1. The output power developed at unity power factor with excitation equal to 1.25 of rated voltage. 2. The load angle and power factor if the generator supplies (1500 KW) at rated voltage and excitation lequal to (1.2) of rated voltage. 3. Repeat part (2) when .armature resistance is neglected
Questions:-1. What is the basic different between the internal characteristics and the external characteristics of d.c shunt generator? 2. For which reasons its not possible to develop rated voltage of d.c shunt generator, both in unloaded and loaded conditions? 3- What are the reasons of fall of terminal voltage of a d.c. shunt generator?
A 3 phase, star connected synchronous generator supplies current of 10A having phase angle of 20º lagging at 400V. Find the load angle and the components of armature current Id and Iq if Xd = 10 ohm and Xq = 6.5 ohm Assume armature resistances to be negligible
A 70-MVA, 69.3-kV, three-phase round-rotor synchronous generator has a synchronous reactance of 14 ohm per phase and negligible armature resistance. 1) The generator is delivering rated power at 0.87 power factor lagging at the rated terminal voltage to an infinite bus bar (Fig. 1). Determine the magnitude of the generated emf per phase and the power angle δ. 2) The generator is delivering 53.5 MW to the bus bar at the rated voltage with its field current adjusted for a generated emf of 46 kV per phase. Determine the armature current and the power factor. Is the power factor is lagging or leading? 3) Given that the generator is operating at the excitation voltage of Part (1), determine the maximum steady-state power which the machine can deliver without losing synchronism. Find the armature current corresponding to this maximum power.
EMachines A 100 MVA, 11.5 kV 0.8 pf lagging 50-Hz two pole Y-connected synchronous generator has a per-unitsynchronous reactance of 0.8 and per-unit armature resistance of 0.012. A. What is its synchronous reactance and armature resistance in ohms?B. What is the magnitude of the internal generated voltage at the rated conditions? What is its torque angleat these conditions?C. Ignoring losses in this generator, what torque must be applied to its shaft by the prime mover at fullload?
Energy Question-1) Three identical synchronous generators were connected in parallel and the idle frequency values of each generator were set to 54 Hz. The frequency - power characteristic slopes of the first and second generators are 5.3 MW/Hz and the slope of the third generator is 3.9 MW/Hz. When these three identical synchronous generators feed a load together, the system frequency becomes f=51.7 Hz. According to this;a-) Calculate the active power value that the first generator will provide to the load.b-) Find the active power that the second generator will provide to the load.c-) Find the active power that the third generator will provide to the load.d-) Calculate the power of the load.(All values in options a, b, c, and d in this Question will be entered as two digits after the comma.) NOTE: If the information in the text and the photo is different, please solve the question using the information given in the photo. Help me please... Thank you so much.
A 440 V, 3-phase, delta connected cylindrical synchronous motor with synchronous reactance of Xsm=2Ω is connected to a turbo-generator with Xsg=3Ω through transmission line of reactance Xtr=1.5Ω. If its field current is adjusted to give an excitation voltage of 12 Kv, then Calculate: (a) Calculate the maximum magnitude of the resultant flux emf? (b) Calculate the magnitude of armature current and its P.F? (c) Calculate the magnitude of the armature current in phase with stator voltage? (d) Calculate the maximum power output from the motor? (e) Compute the excitation voltage Ef on a per unit basis, when the generator is delivering rated KVA at rated voltagee and at power factor of (i) 0.8 lagging and (ii)0.8 leading? (f) Draw the complete phasor diagram and show that armature current leading the terminal voltage?
A three-phase, Y-connected, 220 V, 5 kVA, salient-pole synchronous generator is employed to supply power to a load with unitary fp. By means of a slip test, the direct-axis synchronous reactance is determined to be 12 Ω and the quadrature-axis synchronous reactance, 7 Ω. Consider that the rated current is delivered to the load at the rated voltage and that the armature resistance is negligible. (a) Calculate the corresponding value of the excitation voltage. (b) What is the value of the internal phase shift angle? (c) What is the value of the power angle?
4. A 6 pole wave wound shunt generator delivers 200A at a terminal voltage of 240V. Ra and Rsh are 0.03Ω and 70Ω respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv) Power developed. armature current ? current per parallel path ? generated voltage ? Power developed ?
DC Electric Machine: synchronous machine: Which option is correct for the graph given regarding the synchronous machine? The order should be: name of the characteristic / run in (1) / run in (2) / run in (3) A) Idle running characteristic of the motor / capacitive / ohmic / Inductive. B) Setting characteristic of the generator / Pure inductive / ohmic / Pure capacitive. C) Setting characteristic of the generator / Inductive / ohmic / capacitive. D) External characteristic of the generator / capacitive / ohmic / Inductive. E) External characteristic of the motor / Inductive / ohmic / capacitive
4. Why is the fall in the terminal voltage for the external characteristic greater in shunt generator than in separately – excited generator?