Q17: A fully-controlled three-phase bridge rectifier circuit is modified by placing acommutating diode across the highly inductive load (load current is continuous andlevel). Draw the waveform of the output voltage and calculate the mean value of theoutput voltage for a=90° and 380 V L-L three phase AC supply voltages.e torqQ18: For single-phase half- wave controlled rectifier circuit with inductive load (L-0.1 Hand R=102) and the AC supply is 240V ,50Hz. Let the firing angle of the thyristoris a=90°. Find the value of the load current at the time (t=0. 005 s). Assume t-0 atthe instant of firing.

As it is not mentioned which question is to be solved I am solving the first question as per our…

Q17: A fully-controlled three-phase bridge rectifier circuit commutating diode across the highly inductive load (lo level). Draw the waveform of the output voltage and cal output voltage for a-90° and 380 V L-L three phase A.

Q17: A fully-controlled three-phase bridge rectifier circuit commutating diode across the highly inductive load (lo level). Draw the waveform of the output voltage and cal output voltage for a-90° and 380 V L-L three phase A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
If a diode full wave rectifier circuit is excited by an ac source with an amplitude of 10 V and angular frquency of 100 rad/sec, then what will be the amplitude of the dc voltage obtained at the output of the rectifier? Assume no filter circuit is used.
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
A single-phase full-wave rectifier uses a power transformer whose secondary voltage is 220V r.m.s. The load resistor is 100kΩ. Neglect the transformer losses and the forward drops in the diodes. Determine the following: DC output voltage 2. Ripple voltage
A 5V dc stabilized power supply needed to operate a computer is to be produced from a 12V full-wave bridge rectifier using a Zener diode as the regulator circuit. The maximum power rating of the zener diode , Pz is 6W. Calculate the following Maximum current flowing through the zener diode. Value of the series current limiting resistor, Rs. ii. Load current, lc if the load resistor is 50kΩ
Find the peak output voltage for the bridge rectifier. Also, assuming ideal diodes, find the PIV rating required for the diodes. The transformer is specified to have 12 Vrms secondary voltage for the standard 110 V across the primary.(Show complete solution)
2. Design a full wave rectifier for a regulator that delivers 100W electrical power to a white off-the-shelf LED. Per datasheet, the LED requires 33V and draws 3A current. You are required to limit the ripple voltage to less than 20% of average DC voltage of the output. Assume all diodes have Von=0.7V and negligible off current.a. Draw the circuit diagram.b. Determine the voltage of transformer and capacitance of the filter
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False