Q1/A motor having a suitable control circuit develops a torque given by the relation Tm = a w² + 4 %3D where a is positive constant. The motor is used to drive a load whose torque is expressed as: - T = c w + 3 where c is positive constant. The total inertia of the rotating masses is J a) Under these conditions, the motor can be starting? b) Calculate the equilibrium operating speed.

Q1/A motor having a suitable control circuit develops a torque given by the relation Tm = a w² + 4 %3D where a is positive constant. The motor is used to drive a load whose torque is expressed as: - T = c w + 3 where c is positive constant. The total inertia of the rotating masses is J a) Under these conditions, the motor can be starting? b) Calculate the equilibrium operating speed.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

A 64-lb weight is attached to a vertical spring, causing it to stretch 3 in. upon coming to rest at equilibrium. The samping constant for the system is 3 lb·sec/ft. An external force F(t) = 3 cos(12t) lb is applied to the weight. Find the steady-state for the system. Note that g≈32 ft/s2
The equivalent spring stiffness of an inclined spring whose k = 5 N/m and angle of inclination θ = 35° 3.355 N/m 4.095 N/m 5.867 N/m 4.511 N/m
Mechanical Engineering In a lamellae clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
Q.2 stroke engine develops 60 kw.If the brake thermal efficiency 80%, fuel is 42 MJ/kg and mechanical efficiency is 80%, determine, a) Fuel consumption b)lndicated power c)lndicated thermal efficiency
A flywheel absorbs 2500 ft-lb of energy at a coefficient of fluctuation of 0.10. The mean diameter of the flywheel is 72 inches. The weight of the arms and hub is 12 % of the rim weight. The mean rim speed is 80 fps. Consider the specific weight of the flywheel as γ = 0.26 lb/in3. A. Find the mean rpm of the rim. B. Determine the weight of the rim. C. What is the cross sectional area of the rim?
1.Find out by direct derivation the relation between a spring's effective and actual mass. 2. Is it the same of a static measurement of k as it is for a dynamic measurement?
1.A rotor has an inner radius of 10.0 cm and an outer radius of 25.0 cm. It is fixed to a frictionless axle that goes through its center. The moment of inertia (I) of the rotor is 0.0235 kg m2. A set of 5 constant forces act on the rotor, as shown in the diagram below. (a) Find the net torque acting on the rotor, in units of Nm. Be sure to give both the magnitude and direction. (b) Find the angular acceleration of the rotor, in units of rad/s2. Give both the magnitude and direction. (c) Assuming it starts from rest at t = 0, how long does it take for the rotor to reach an angular speed of 565 revolutions pre minute (rpm)? Give your answer in seconds. (d) At t = 2.50 seconds, how many complete revolutions will the rotor have made?
Problem Solving. Solve the following problems completely. 5. Motors from two different manufacturers are being considered for application.Both motors are 50Hp, 460 volts, 3 phase, 60 cycles. Motor A operates at 80%efficiency and motor B operates at 89% efficiency. The expected need for themotor is 15 years. Motor A cost P120, 000.00 and motor B P150, 000.00.Electrical energy cost P8.00 per Kw-Hr and the motors will be operating 8 hoursper day, 250 days a year. Assume taxes and insurance are 3% of first cost. Whichmotor should be purchased?
Which of the following terms is applied to the study of systems in a constant state of motion? Select one: a. dynamics b. statics c. plyometrics d. anthropometrics
20. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the vehicle resumes moving. One way to do this is to “store” the energy in a spinning flywheel. One such design uses a solid disk flywheel with moment of inertia 0.040 kg m2 and maximum rotation rate 45000 rpm. (a) What is the maximum energy storage? (b) In principle it could store the kinetic energy of a 1700 kg car moving at what speed before braking? (c) If this energy is used to start the car moving again in 10.0 s, what is the power output of the system?
The end of a spring is pulled to the right by 4 cm; the restoring force is8 N to the left. Given the relationships 8.15c, if the spring is returned to equilibrium and then pushed to the left by 2 cm, the restoring force isA. 4 N to the left. B. 4 N to the right. C. 8 N to the left.D. 8 N to the right. E. 16 N to the left. F. 16 N to the right.
5) As a continuation of the 1st question, let's assume that we find the required engine power P=5 kW while pulling the wagon up in the wagon system in Kardemir. Let's wrap the rope around the drum at v=6 m/s while pulling the wagon up steadily at the desired speed (don't take anything from question 1. Just think of it as a continuation). If the revolution of the motor we will buy from the market is n= 2500 rpm, accordingly, the RB=? what should we get the radius of the gear? We want to get the radii of the other gears RA = 61 mm, RD = 147 mm.