Q2) A 3-phase load of 5 MW at a power factor of 0.9 lagging is to betransmitted over a distance of 100 km with a receiving end voltage of 66kV, 50 Hz. Each conductor has a resistance Of 0.8 2 /km and radius of26.1 mm, the conductors have an equilateral spacing of 2 m. Find thesending end voltage, current and power factor, by using: 1) Nominal acircuit method. 2) Nominal T circuit method.

Answered: Image /qna-images/answer/89c6a90c-a3c9-44b0-8835-a41f32e31c9e.jpg

Q2) A 3-phase load of 5 MW at a power factor of 0.9 lagging is to be transmitted over a distance of 100 km with a receiving end voltage of 66 kV, 50 Hz. Each conductor has a resistance Of 0.8 Q /km and radius of 26.1 mm, the conductors have an equilateral spacing of 2 m. Find the sending end voltage, current and power factor, by using: 1) Nominal a circuit method. 2) Nominal T circuit method.

Q2) A 3-phase load of 5 MW at a power factor of 0.9 lagging is to be transmitted over a distance of 100 km with a receiving end voltage of 66 kV, 50 Hz. Each conductor has a resistance Of 0.8 Q /km and radius of 26.1 mm, the conductors have an equilateral spacing of 2 m. Find the sending end voltage, current and power factor, by using: 1) Nominal a circuit method. 2) Nominal T circuit method.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

Consider a three-phase generator rated 300MVA,23kV, supplying a system load of 240 MA and 0.9 power factor lagging at 230 kV through a 330MVA,23/230Y-kV step-up transformer with a leakage reactance of 0.11 per unit. (a) Neglecting the exciting current and choosing base values at the load of 100 MVL and 230 kV. Find the phasor currents IA,IB, and IC supplied to the load in per unit. (b) By choosing the load terminal voltage IA as reference, specify the proper base for the generator circuit and determine the generator voltage V as well as the phasor currents IA,IB, and IC, from the generator. (Note: Take into account the phase shift of the transformer.) (C) Find the generator terminal voltage in kV and the real power supplied by the generator in MW. (d) By omitting the transformer phase shift altogether, check to see whether you get the same magnitude of generator terminal voltage and real power delivered by the generator.
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.
The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C and a 60-Hz resistance of 0.0956 ohm per mile at 50C for the all-aluminum Marigold conductor, which has 61 strands and whose size is 1113 kcmil. Assuming an increase in resistance of 2 for spiraling, calculate and verify the dc resistance. Then calculate the dc resistance at 50C, and determine the percentage increase due to skin effect.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
For a balanced three-phase positive-sequence currents Ia,Ib,Ic, does the equation Ia+Ib+Ic=0 hold good?
For the case of double-circuit, bundle-conductor lines, the same method indicated in Problem 4.27 applies with r' replaced by the bundles GMR in the calculation of the overall GMR. Now consider a double-circuit configuration shown in Figure 4.36 that belongs to a 500-kV, three-phase line with bundle conductors of three subconductors at 21 in. spacing. The GMR of each subconductor is given to be 0.0485 ft. Determine the inductive reactance of the line in ohms per mile per phase. You may use XL=0.2794logGMDGMR/mi/phase
An Overhead transmission line has a span of 115 m. Ultimate strength is 3600 Kg and factor of safety is 2. If the sag is 3 m, If the weight due to wind is 1.5 kg/m, Determine(a) weight of the conductor and(b) Length of the line
Given a three-phase load of 125 MW at power factor of 0.8 lagging, operating at 69kV, with a transmission line efficiency of 97% and voltage regulation of 95%, and the line length of 50 km, design a transmission line system and determine the best conductor configuration, conductor resistance and inductance, and conductor radius values to achieve the efficiency and voltage regulation set. Assume a two-bundled conductor configuration with GMR of 0.0496 m and bundle spacing of 30 cm.
Given a three-phase load of 125 MW at power factor of 0.8 lagging, operating at 69kV, with a transmission line efficiency of 97% and voltage regulation of 95%, and the line length of 50 km, design a transmission line system and determine the best conductor configuration,conductor resistance and inductance, and conductor radius values to achieve the efficiencyand voltage regulation set. Assume a two-bundled conductor configuration with GMR of 0.0496 m and bundle spacing of 30 cm.
Q1: a) Discuss the effect of earth on the capacitance of a line : b) Derive in expression for the capacitance to neutral per phase per Km of a single phase overhead transmission line, taking into account the effect of earth. c) Derive in expression for the capacitance to neutral per phase per Km of a 3- phase overhead transmission line when conductors are of equilateral spacing.
A three-phase transposed line is composed of one ACSR Bobolink conductor per phase with a horizontal spacing of 11 meters as shown in the figure. phase with a horizontal spacing of 11 meters as shown in the figure. The conductors have a diameter of 3.625 cm and a RMG of 1.439 cm. Calculate the inductance and capacitance to the neutral of the line.