Q2: A conveyor beam has the cross section shown below and it is subjected to a ben moment. Determine the maximum permissible bending moment which can be applie the heam when the hottom flange in tension, if the safe stannen for the materia /**** tension and compression are 30 MPa and 150 MPa respectively. T C - 25 mm F 150 mm 100 mm 50 mm *50*100*50* mm mm mm

Q2: A conveyor beam has the cross section shown below and it is subjected to a ben moment. Determine the maximum permissible bending moment which can be applie the heam when the hottom flange in tension, if the safe stannen for the materia /**** tension and compression are 30 MPa and 150 MPa respectively. T C - 25 mm F 150 mm 100 mm 50 mm 5010050 mm mm mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

l4//me shear and bending moment diagram as shown in figure. by graphical method. 132.5KN 122.5KN.m ) sgN/m b itwd L oe—dine—d
1. A thin high-strength steel plate having a thickness of 40 mm has a height of 120 mm and length of 350 mm, is subjected to a moment at both ends = 66 kN.m. E = 28000 MPa Determine the bending stress of the steel plate in MPa a. 1440 b. 1855 c. 1344 d. 2063 e. 2333 Determine its radius of curvature in mm. a. 272 b. 558 c. 154 d. 434 e. 166 2. According the NSCP 2015, the first hoop for beams and girders shall be located not more than 50 mm from the face of the supporting columns. The maximum spacing of hoops shall not exceed... a. 150mm b. d/4 c 6 times bar diameter d. all of the above 3. Based on NSCP 2015 Seismic requirement on concrete girders (beams with special moment frames, which of the following most nearly gives the required width (bw) of beam if its overall height is 600 mm. a. 250mm b. 180mm c. 300mm d. 350mm e. 400mm PLEASE ANSWER ALL
A cold drawn steel rod of circular cross-section is subjected to a variable bending moment of 565 Nm to 1130 N-m as the axial load varies from 4500 N to 13 500 N. The maximum bending momentoccurs at the same instant that the axial load is maximum. Determine the required diameter of the rodfor a factor of safety 2. Neglect any stress concentration and column effect. Assume the followingvalues:Ultimate strength = 550 MPaYield strength = 470 MPaSize factor = 0.85Surface finish factor = 0.89Correction factors = 1.0 for bending= 0.7 for axial load
Draw the shearing-force and bending-moment diagrams for the following beams: 1. A cantilever of length 20 m carrying a load of 10 kN at a distance of 15 m from the supported end. 2. A cantilever of length 20 m carrying a load of 10 kN is uniformly distributed over the inner 15 m of its length. 3. A cantilever of length 12 m carrying a load of 8 kN, applied 5 m from the supported end, and a load of 2kNlm over its whole length.
get the support reactions get the shear and moment diagram get the shear and moment equations where L1= 3m, L2 = 4m and W1 = 7KN/m
W=464KN/m Using Three Moment Equation, determine all reactions at supports also, determine shear and bending moments with complete labels. Use I= 1/12 bh^3 and E = 2.15x10^7 KPa
The maximum bending stress of a hollow shaft is equivalent to 80N/mm2, while the maximum shear stress is equal to 70 N/mm2.The shaft rotates and loads are applied suddenly, with minor shocks. Determine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2100 N-m and a torque of 4100 N-m if the thickness of the hollow shaftis equal to 0.15of the outer diameter of the shaft. Apply ASME Code for this problem.
A shaft is made of a polymer having an elliptical cross section. If it resists an internal moment of M = 50 N # m, determine the maximum bending stress in the material (a) using the flexure formula, where Iz = 1 4 p(0.08 m)(0.04 m)3, (b) using integration. Sketch a three-dimensional view of the stress distribution acting over the cross-sectional area. Here Ix = 1 4 p(0.08 m)(0.04 m)3.
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
A loaded beam, 60 mm wide by 100 mm high and 6 m long, has the shear and moment diagrams as shown below. Determine (a) the magnitude, type and location of the maximum flexural stress (in MPa) (b) the stress (specify the type) in a fiber 30 mm from the top of the beam at a section 3.5 m from the left end. I = bh3/12
A picture is taken of a man performing a pole vault, and the minimum radius of curvature of the pole is estimated by measurement to be 4.5 m. If the pole is 40 mm in diameter and it is made of a glass-reinforced plastic for which Eg = 131 GPa, determine the maximum bending stress in the pole.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.