Q2) Figure 2 shows the zone of capillary rise within a clay layer above the groundwatertable. For the following variables, calculate and plot o, u, and ở with depth.Note: H1=4m, H2=2.5m, H3=4.5m, Degree of saturation in capillary rise zone, S (%)=60%G = 2.69; e = 0.47G = 2.73; e = 0.68G = 2.7; e = 0.89Dry sandO Clay; zone of capillary riseClayRockFigure 2

Given data Dry sand Clay Rocks Zone of Cappilary rise Void ratio Specific gravity

Q2) Figure 2 shows the zone of capillary rise within a clay layer above the groundwater table. For the following variables, calculate and plot o, u, and ờ with depth. Note: H,=4m, H2=2.5m, H3=4.5m, Degree of saturation in capillary rise zone, S (%)=60% G = 2.69; e = 0.47 G, = 2.73; e = 0.68 G = 2.7; e = 0.89 Dry sand Clay; zone of capillary rise Clay Rock Figure 2

Q2) Figure 2 shows the zone of capillary rise within a clay layer above the groundwater table. For the following variables, calculate and plot o, u, and ờ with depth. Note: H,=4m, H2=2.5m, H3=4.5m, Degree of saturation in capillary rise zone, S (%)=60% G = 2.69; e = 0.47 G, = 2.73; e = 0.68 G = 2.7; e = 0.89 Dry sand Clay; zone of capillary rise Clay Rock Figure 2

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.13P

See similar textbooks

Similar questions

Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the coefficient =0.05 m/s and porosity p =48%, find the transmissibility (T) in m/s per unit m, if the aquifer width is 1.2 m. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.
Consider two horizonal soil layers, each is isotropic, the upper layer 1 is sitting directly on the top of bottom layer 2. Layer 1 has a thickness of 2 m and a hydraulic conductivity of 0.26 m/day and layer 2 has a thickness of 4 m and a hydraulic conductivity of 0.95 m/day. In this case, calculate the equivalent horizontal hydraulic conductivity in m/day.
L = 370 mm A = 145 cm^2 h = 340 mm Water collected in 3 min Q = 580 cm^3 Void ratio of sand e= 0.66 Determine the Hydraulic conductivity and seepage velocity.
Determine the horizontal and vertical equivalent hydraulic conductivity for the following stratified soil. Take depth of each layer equal to 1.25 m Layer Hydraulic Conductivity (cm/s) 1 0.003 2 0.0003 3 0.002 4 0.0004
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.
The figure shows water flowing through saturated soil in the hatched area. Calculate the elevation pressure and total heads at points A, B and C. If the coefficient of permeability of the soil in the hatched area is 5 cm/sec and the cross sectional area of the soil sample is 15m2 calculate the water flow rate through the soil.
Water flows through a fully confined sand aquifer with a piezometric head gradient of 0.025.(a) If the hydraulic conductivity and effective porosity of the aquifer are 1.72 m/d and 0.45, respectively, estimate the specific discharge and seepage velocity in the aquifer.(b) estimate the volumetric flow rate of the groundwater if the aquifer is 45 m deep and 1.2 km wide.(c) How long does it take a dissolved contaminant in the groundwater to move 1 km?
From the figure shown, H1 = 0.60, H2 = 0.90 m. and h = 0.45 m. The sad has a saturated unit weight of 18.65 kN/m3 . Hydraulic conductivity of sand K = 0.12 cm/sec. If the cross sectional area of tank = 0.46 m2 , determine the following: 1. Total stress and Effective stress at C. 2. Pore water pressure at C. 3. Rate of upward seepage of water in liters/sec.
A soil profile consists of a clay layer of 10 m thick between a permeable sand layer above and an impermeable rock layer below, the water table being in the sand layer. Before the construction of a reservoir raft foundation, piezometers were installed in the clay layer.The whole process of filling the reservoir may be approximated to applying rapidly a single pressure increment of 100 kN/m2 uniformly throughout the clay layer. One year after filling the reservoir, the settlement was 20 cm and the piezometers indicated the distribution of excess pore pressure as shown in the figure below. Estimate the final settlement and the time to complete 90 % of primary consolidation.
Question 32 A dense silt layer has the following properties: void ratio = 0.66, specific gravity = 2.5. Free ground water is 9.47 m. below the ground. Capillary action rise will reach 6.66 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 52.77%. Determine the effective pressure (in kPa) at a depth of 7.42 meters from the ground surface. Round off to three decimal places.
35.) A dense silt layer has the following properties: void ratio = 0.75, specific gravity = 2.59. Free ground water is 9.49 m. below the ground. Capillary action rise will reach 6.69 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 50.02%. Determine the effective pressure (in kPa) at a depth of 7.51 meters from the ground surface. Round off to three decimal places.