The cross-section of an earth dam is shown in figure below. Assuming that the water level remains constant at 35m, determine the seepage loss through the dam. The width of the dam is 300m, and the soil is anisotropic with k.-8.3*107 m/s and k, =3.2 10“ m/s. determine the seepage loss through the dam?

The cross-section of an earth dam is shown in figure below. Assuming that the water level remains constant at 35m, determine the seepage loss through the dam. The width of the dam is 300m, and the soil is anisotropic with k.-8.3*107 m/s and k, =3.2 10“ m/s. determine the seepage loss through the dam?

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.3P

See similar textbooks

Similar questions

11. A channel runs almost parallel to a river as shown in the figure. The water level in the river has an elevation of 36 m. and the elevation of the channel is 33 m. The river and channel are 600 m apart and a previous formation of the average thickness of 9 m and hydraulic conductivity of 0.80 m/hr joints them together. Compute the hydraulic gradient Compute the rate of seepage flow from the river to the channel per meter width in liters per day. If the seepage velocity is 0.048 m/day, compute the void ratio of the previous medium.
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.
9. From the figure shown: (See picture below) Cross-sectional area = 0.6m2 Hydraulic Conductivity of sand = 0.1 cm/sec What is the rate of upward seepage of water? (Answer: 360 cm3/sec) What would be the critical hydraulic gradient? (Answer: 1.12 m) What value of h to cause boiling? (Answer: 2.8 m)
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
A 10 m clay stratum is overlaying a rock stratum. If water table is at the ground surface, calculate the overburden soil pressure at the middle of the clay layer using the ff. properties of clay: ∂sat = 17.95 kn/m3, e = 1.1 , LL = 60%
Find the rate of flow in m^3/sec/m (at right angles to the cross-section shown in Figure 7.33) through the permeable soil layer. Given: H 4 m, H1 2 m, h 2.75 m, S 30 m, a 14°, and k 0.075 cm/sec.
Refer to Problem 8.4. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure per meter length (measured along the axis of the structure).8.24 For the hydraulic structure shown in Figure 8.24, draw a flow net for flow through the permeable layer and calculate the seepage loss in m3/day/m.
Use 10 kN/m3 for unit weight of water. For a concrete structure that retains water, a flow net is sketched as shown in Figure H8-3. Noting the marked location of the Datum, answer the following: Mark on the figure all boundary Also mark the type of each boundary. Calculate the uplift pressures at points A, B, C, D, E, and F. Calculate the factor of safety against The seepage loss (q) per day per meter length of the (i.e. q in m3/day/m) if the permeability of the soil is k = 10-4 m/sec.
For the two-dimensional flow system shown below (units in meters):Compute the total flow rate under the Dam. X = 4, Y = 8. Note 1: Point A is located in the middle point of the equipotential lines. Point B is located in the middle point of the flow lines.Note 2: Assume e=0.8 (void ratio) and k=10^-3 cm/s (coeff. of permeability).Note 3: Datum is located at the bottom level of the water (right side of Dam).Note 4: Remember, the figure is drawn to scale. So, use the value of 2X+Y to estimate any dimension that you consider necessary.
A soil sample 10 cm in diameter is placed in a tube 1.2 m long. A constant supply of water is allowed to flow into one end of the soil at A and the outflow at B is collected by a beaker. The average amount of water collected is 2 cm3 for every 10 seconds. Determine the hydraulic gradient. Ans: 0.667
A 500 m long levee made of compacted clay impoundswater in a reservoir as shown in attached Figure There is a 1 mthick (measured in the direction perpendicular to the seam)sand seam continuing along the entire length of the levee, at10° inclination to the horizontal, which connects the reservoirand the ditch. The hydraulic conductivity of the sand is2.6 X 10-3 cm/s. Determine the volume of water that flowsinto the ditch every day.
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the coefficient =0.05 m/s and porosity p =48%, find the transmissibility (T) in m/s per unit m, if the aquifer width is 1.2 m. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.