P = 2 MPa T = 400°C V = 50 m/s 21 = 10 m Q4: (Section B) The power output of an adiabatic steam turbine is 5 MW, and the inlet and the exit conditions of the steam are as indicated in Figure. Find: STEAM (1) The work done per unit mass of the steam flowing TURBINE -5 MW through the turbine. (2) The mass flow rate of the steam. Pz = 15 kPa X = 90% V = 180 m/s 22 = 6 m (Use Table A-5-1 and Table A-6-2)

P = 2 MPa T = 400°C V = 50 m/s 21 = 10 m Q4: (Section B) The power output of an adiabatic steam turbine is 5 MW, and the inlet and the exit conditions of the steam are as indicated in Figure. Find: STEAM (1) The work done per unit mass of the steam flowing TURBINE -5 MW through the turbine. (2) The mass flow rate of the steam. Pz = 15 kPa X = 90% V = 180 m/s 22 = 6 m (Use Table A-5-1 and Table A-6-2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg.
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.
Write legibly so i can understand 3. The turbine section of a Brayton cycle gas turbine receives hot compressed air at 150 psia and 2100 o R, expands it to 15 psia and develops a gross output of 15,000 HP. Air enters the compressor at 500 R. Determine: d.) thermal efficiency, e) mean effective pressure (psia)
A R-12 compressor operates betwwen eveoperating temperature of 4 c ( hg = 353 kj/kg ), vg = 0.04895) and condensing temperature of 43 c ( hf = 241.6 kj/kg ).determine the bore diameter of the 4 cylinder 1000 rpm compressor if the piston speed is 200 meter/min and actual volumeter efficiency is 82% and refrigeration load is 25 tons
Steam in an adiabatic turbine expands from a pressure of 6 MPa and a temperature of 300 °C to a pressure of 0.1 MPa, with a flow rate of 3 kg/s. If Steam leaves the turbine as saturated steam, what is the turbine's power output? last 2 min
The water in a large reservoir in the figure is transported to the turbine - generator group by a 1 m diameter penstock, where the energized fluid is released into the river. The net head of the turbine is calculated as 85 m. If the fluid flow through the penstock is 9 m3 / s and the efficiency of the turbine - generator group is 85%, what is the generator output power? Assume that the water velocity at the river outlet of the turbine is zero and the water level in the tank remains constant. Take the density of the water as 1000 kg / m3 and the gravitational acceleration as 10 m / s2.
For example, suppose you had 5.0 kg/s of water at 1 MPaa and 500 degrees Celsius that enters an ideal steadystate, steady-flow turbine and, following isentropic expansion, exhausts at 0.025 MPaa: ΔP = 0, and ΔK = Calculate: if the turbine's efficiency is 90 percent, calculate the steam quality or temperature of steam at turbine exhaust, as well as the turbine output. (Draw the diagram)
Water at 180 degrees Celsius (Psat = 1.0 MPa) and 13 MPa enters a boiler. It then leaves the boiler at 500 degrees Celsius. What is the mass flowrate of water?
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
Q.9 Steam is expanded isentropic ally in the high pressure cylinder of a steam turbine from a pressure of 2 Mpa at 350 °C to 0.1 Mpa. Isentropic expansion is then continued down to 7 KN/m2 in the low pressure cylinder. Calculate the percentage of the total work output that is performed by the H.P cylinder.
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 oC. the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 o the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram i. Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. ii. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.