Q2: In the circuit shown in Figure 2 calculate a) load current and voltage b) average and reactive power delivered to the load. c) average and reactive power delivered to the line. d) average and reactive power supplied by the source. 1Ω j4 N 39 Ωξ 250/0° V (rms) VL IL j26 N Source -Line- - Load

Q2: In the circuit shown in Figure 2 calculate a) load current and voltage b) average and reactive power delivered to the load. c) average and reactive power delivered to the line. d) average and reactive power supplied by the source. 1Ω j4 N 39 Ωξ 250/0° V (rms) VL IL j26 N Source -Line- - Load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Similar questions

In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
A 400-V, 3-phase, 4-wire service mains supplies a star connected load. The resistance of each line is 0.1ohms and that of the neutral 0.2 ohm. The load impedances are Z 1 = (6 + j9) ohms l Z 2 = 8 ohms ; Z 3 = )6 – j8)ohms. Calculate the current in the neutral.e. 56.22 A f. 50.06 A g. 45.18 A h. 49.35 A
4) State the relation between line and phase values of voltage and current for 3-pha se DELTA connected load .state the equation for active, reactive power consumed by 3-phase load.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Consider the microgrid of Figure 3.66. A three-phase transformer, T1, israted at 500 kVA, 220 VY grounded/440 V delta, a transformerwith a reactance of 3.5%.Themicrogridis supplied from anAC bus of a PV generating station.The DC bus rated at 540 V.The distributionlineis 10mileslong and has a series impedance of 0.1 + j1.0 Ω per mile and local load of 100 kVA at 440 V. The microgrid is connected to the local power grid using a three-phase transformer T2, rated at 440 V Y grounded/13.2 kV delta,500 kVA with a reactance of 8%. Compute the per unitimpedance diagram of the microgrid system. Assume the voltage base of 13.2 kV on the local power grid side and kVA base of 500
The power system insulation problem involves a. Capacitance of earth and subsequent grounding b. Selection of basic insulation level of system equipment c. Determination of single phase line insulation d. Determination of three phase line insulation Clear my choice
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Question oneA balanced star connected load comprises of 20 ohm resistance and 0.07 Henry inductance in each branch. If the load supplied with 415V at 50Hz, calculatea) the line currentb) the power factorc) the total power supplied to the load PLEASE FOLLOW THIS APPROACH TO SOLVE THE QUESTION. THANK YOUStep OneDeduce the inductive reactance.STEP TwoWrite down a rectangular expression for the impedance per branch.STEP ThreeConvert the rectangular expression into polar expression.STEP FourBecause impedance will be involved in the analysis deduce the phase voltage.STEP FiveSolve for the phase current and hence the line current.STEPVSixUse the phase angle of the current to deduce the power factor. STEP SevenFind the apparent power.
A three phase,Y connected, 215 V (line to line), 7.5 kW, 60 Hz, three pole IM has the following parameter values in Ohm/phase referred to the statorR₁ = 0.294 Ohm, R₂ = 0.144 Ohm, X₁ = 0.203 Ohm, X₂ = 0.409 Ohm, Xm = 10.25 Ohm.The total friction,windage and core losses may be assumed to be constant at 350 W independent of load. For a slip s = 0.02, compute the followingsa) Stator Currentb) Power Factor(pf)c) Rotor Speedd) Power Output(Shaft)e) Output(Shaft) Torquef) Efficiency(n)
In a house there is a three-wire system configured as follows: A refrigerator with an impedance of (10 + j 10) Ω is connected to line L1 and to a neutral. And to line L2 and neutral all the lighting in the house consisting of 10 luminaires of 20 W each. In addition, there is a 240 V dryer that consumes 8 kW connected between the two lines. Calculate current in line L1, line L2 and neutral total power consumed Problem was Initially stated in spanish, i will add it in case it works. En una vivienda se tiene un sistema trifilar configurado de la siguientemanera. Se tiene conectada a la línea L1 y a neutro una refrigeradora con impedancia de (10 + j 10)Ω y a la línea L2 y neutro toda la iluminación de la casa consistente en 10 luminarias de 20 W cadauna. Además, se tiene una secadora a 240 V que consume 8 kW. Calcule a) corriente de la línea L1 yde la línea L2 y de neutro b) potencia total consumida.
This wind farm needs a 250 km connection laid to Sommerville. The choice is either a 3 phase system or a bipolar dc system at 400 kV and ±400 kV at the receiving end respectively. (i) The 3-phase system has resistive losses per phase of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (ii) The bipolar dc system has resistive losses of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (iii) Calculate the efficiencies of the two systems. (iv) Comment on which system you would choose to use and why.
•••PF improved by 100% Convert the given load of the circuit shown into impedance bulk by using power triangle; f= 60hz. Measure the line current IL, power loss PL0, power source Ps, voltage source VS; take note of the old value of PFL; Notations IL= line current; PL0= power loss; PS= power source; VS= voltage source; PFnew= New power factor after correction; PFold= old power factor before correction