3)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.just write for me the the correct answer. The 3-phase power and line-to-line voltage ratings of the electric power system shown in the followingfigure are as follows:22 KV22 KVGenerator G160 kVAX= 9%Z= 2 +j5 2X= 10%LineTransformer T200 kVA22/0.5 KVMotor M40 kVA0.4 KVX= 8%v,LineMOn a 100-kVA base power and 22 kV base voltage at the generator side,If V, is equal to 1.11 pu, then it is in volts equal to:O a. 1982 VO b. 198.2 VO . 19.82 kVO d. 24.42 VO e. None of these answers is correctO f.24.42 kVO g. 19.82 V

In this question we need to find a voltage in KV or Volt for the given value of Vg

The 3-phase power and line-to-line voltage ratings of the electric power system shown in the following figure are as follows: Generator G 160 kVA 22 KV X= 9% Z= 2 + j5 2 X= 10% X= 8% Line 22 KV Transformer T 22/0.5 KV 0.4 KV 200 kVA Motor M 40 kVA Va Line On a 100-kVA base power and 22 kV base voltage at the generator side, f Vg is equal to 1.11 pu, then it is in volts equal to: О а. 1982 V O b. 198.2 V O. 19.82 kV O d. 24.42 V O e. None of these answers is correct O f. 24.42 kV O g. 19.82 V

The 3-phase power and line-to-line voltage ratings of the electric power system shown in the following figure are as follows: Generator G 160 kVA 22 KV X= 9% Z= 2 + j5 2 X= 10% X= 8% Line 22 KV Transformer T 22/0.5 KV 0.4 KV 200 kVA Motor M 40 kVA Va Line On a 100-kVA base power and 22 kV base voltage at the generator side, f Vg is equal to 1.11 pu, then it is in volts equal to: О а. 1982 V O b. 198.2 V O. 19.82 kV O d. 24.42 V O e. None of these answers is correct O f. 24.42 kV O g. 19.82 V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.48P

See similar textbooks

Similar questions

The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformertested at 50 Hz:Voltage (V) Current (A) Power (kW)LV winding with HV terminals open-circuited: 3810 9.86 8.14HV winding with LV terminals short-circuited: 920 141 10.3
For a 220V, 60Hz single phase voltage controller is used for controlling flow of power in to a circuit consisting load of Xl =12 ohms and R=5 ohms. Which of the following represents the correct value of the maximum power and power transfer? (a) Pmax=9.68 kW, p.f =0.6 (b) Pmax=3.72 kW, p.f =0.6 (a) Pmax=9.38 kW, p.f =0.38 (a) Pmax=1.43 kW, p.f =0.38
A domestic system of a single-phase 3-wire circuit, allows the operation of both 120V and 240V at 60HZ devices. This domestic circuit is modeled as indicated in the figure. Calculate: A) The currents 11, 12 and 13; B) The total complex power supplied; C) The total power factor of the circuit.
A generator is rated 100 MW, 13.8kV and 90% power factor. The effectiveresistance is 1.5 times the ohmic resistance. The ohmic resistance isobtained by connecting two terminals to a DC source. The current andvoltage are 87.6 A and 6 V respectively. What is the DC resistance perphase? What is the effective resistance per phase? Whole Solution
The electrical power supply system of a particular country is made of the following. Draw asingle line diagram of the electrical power supply system of the country based on the informationbelow using any computer-aided software.Power supply from an infinite bus bar S connected to bus bar A, through a circuit breakerconnected between isolators and a three-phase delta/star solidly earthed transformer T1.Powersupply source from a generator G1 connected to bus bar B through a circuit breaker connectedbetween isolators, and a three- phase delta/star solidly earthed transformer T2. power supplysources from two generators G2 and G3. Each of the generators are connected to a reactor.Furthermore, each of the generators connected to a common bus bar C through a circuit breakerconnected between isolators and a three-phase star/star solidly earthed transformer T3 and T4respectively. bus bar F to bus bar A by means of two isolators, one at each end of transmissionline L6; bus bar A to bus bar E by…
3-phase ,50Hz overhead transmission line has the following constanats: resistance/phase=9.6ohms inductance/phase=0.097ohms capictance/phase=0.765uf if the line is supplying a balanced load of 24,000KVA 0.8 p.f lagging at 66kv calculate : sending end current line value of sending end current sending end power factor percentage regulation transmission efficiency
This wind farm needs a 250 km connection laid to Sommerville. The choice is either a 3 phase system or a bipolar dc system at 400 kV and ±400 kV at the receiving end respectively. (i) The 3-phase system has resistive losses per phase of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (ii) The bipolar dc system has resistive losses of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (iii) Calculate the efficiencies of the two systems. (iv) Comment on which system you would choose to use and why.
Ascertain the Actual values of the following given parameters 200mvA, 13.8kv generator which has a reactance of 0.85 pu and is generating 1.15pu voltage. a) Line voltage b) Phase voltage c) Reactance d)line and phase voltage with the new base of 500MVA, 13.5KV
Two loads connected according to the diagram below are connected to a three-phase network. All impedance elements are pure resistances and the two three-phases are symmetrical. Voltmeter V1 shows 250 V and voltmeter V2 shows 433 V. a) Calculate the voltage between L1 and L2 b) Calculate the current ID . c) Calculate the current IL . d) How big is cosφ1
A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 20 and 15 A respectively and are fed from the cable at distance of 25 and 10 respectively. Calculate the voltage available across load 1 and 2. a- Voltage across load A is, Va= b- Voltage across load B is, Vb=
KINDLY ANSWR IMMEDIATELY, THANKYOU FOR HELPING OUT An electric utility company runs two 100 m copper wires from the street mains up to a customer's premises. If the wire resistance is 0.10 per 1000 m, calculate the line voltage drop for an estimated load current of 120 A. CHOICES: A. 1.4 V B. 3.4 V C. 4.4 V D. 2.4 V
Question. Consider a 4 kIA, 200/400V single-phase transformer supplying fiulload current at 0.8 leading power factor. The O.C/S.C test results are as follows: O.C test : 200 V, 0.8A, 70 W (L.V side)S.C test : 20 V, 10A, 60 W (H.V side)Calculate efficiency, secondary voltage and current into primary at the above load.