Q2) The figure below represents a hydraulic car jack has an output cylinder 30 cm in diameter and an input cylinder 5 cm in diameter and is filled with oil of density 900 kg/m 3. An automobile of mass 1200 kg needs to be elevated 35 cm. (a) How far does the piston of the input cylinder need to move? (b) What is the magnitude of the force on the input piston required to keep the car elevated? Imput end 44, - A4 Output end up by a distance , area A, ass 3 initial position initial position area A down by a distance h, Points (a) and (b) are at the same level fluid of density pP

Q2) The figure below represents a hydraulic car jack has an output cylinder 30 cm in diameter and an input cylinder 5 cm in diameter and is filled with oil of density 900 kg/m 3. An automobile of mass 1200 kg needs to be elevated 35 cm. (a) How far does the piston of the input cylinder need to move? (b) What is the magnitude of the force on the input piston required to keep the car elevated? Imput end 44, - A4 Output end up by a distance , area A, ass 3 initial position initial position area A down by a distance h, Points (a) and (b) are at the same level fluid of density pP

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a combinational circuit with three inputs (E,L,Y) and three outputs (F,R,A). If the input is less than 5, then the output is 2 greater than the input. Otherwise, the output is 3 less than the input. if E=0 L=0 and Y=0, then if E=0 L=0 and Y=1, then if E=0 L=1 and Y=0, then if E=0 L=1 and Y=1, then…
Q2. Design a digital circuit that indicates via an LED output whether a 4-bit unsigned number is a Lucas number (TRUE=1) or not (FALSE=0) (see Wikipedia). In this question, the input to the circuit should be assumed to be from a decimal keypad (0-9). Therefore, the behaviour of the circuit does not matter when then the input value is greater than 9. This should be taken advantage of in the design process. The steps are:(a) State the truth table for the circuit.(b) State the Karnaugh map for the circuit.(c) Group the 1-cells according to the Karnaugh map technique.
8.7 MECT361 Mechatronics Components and Instrumentation 8.7. Given a 12-bit A/D converter operating over a voltage range from - 5 V to 5 V, how much does the input voltage have to change, in general, in order to be detectable? PLEASE GIVE ME THE REFRENCE I Will get zero if you didn't put the refrence
MechatronixOne is a manufacturer of an industrial and toy robots. They are in the planning stage to develop a prototype AI robot for industry that will be supplied by a 12V dc. This AI robot as they envision has a capability to understand little English command and can interpret it. Their problem is how to design an RC filtered power supply that can be used in their prototype AI robot which has a load range of 250Ω to 1.25k Ω and since this is just a prototype it must be wired to the 220V peak ac supply in their laboratory. They ask the VoltageMaker Company to ship them 20 pcs of 12V dc power supply and it must be included in the data sheet the load current in rms and peak, the PIV, the power range absorbed by the load, the ratio of the transformer, and the secondary rms voltage of the power supply. The power supply must be in a bridge type. But sad to say the company is not producing this type of power supply. The management of VoltageMaker tasks their design engineer team to develop…
A system has an input of a voltage of 3 V which is suddenly applied by a switch being closed. What is theinput as an s function?
1. What are the control methods for electromechanical systems. What arethe advantages of each method? 2. You need to design a quantizer for a sensor which measures voltagevalues between 40 V and 200 V. If your resolution is 4 (n value) findthe number of output states (N) and quantization step (Q). 3. Design a capacitive transducer to be able to measure the displacementof a rotating element in a machine. Sketch the diagram and specifywhich parameters will let you measure the displacement.
proof the equation 10.8 which represents the gain of inversting amplifer ... the proof is already exist in page 621 but there are some expressions were missed before the equation 10.7, you should start this proof from the begining and adding that missed expressions.
subject: Communication Fundamentals Modulation and Demodulation (give solve sub-parts iv and v)
Figure shows a system with two inputs and two outputs. Derive C(s)/R(s), C1(s)/R2(s), C2(s)/R(s), and C(s)/R(s). (In deriving outputs for R(s), assume that R2(s) is zero, and vice versa.)
Discuss two latest Displacement measuring sensors/transducers, that are readily available in the market are being used to measure the displacement (one for translational displacement and 2nd for rotational displacement) of some physical quantity, generated by some force/pressure/temperature or acceleration and translated into displacement.
MechatronixOne is a manufacturer of an industrial and toy robots. They are in the planning stage to develop a prototype AI robot for industry that will be supplied by a 12V DC with Izm = 20mA. This AI robot as they envision has a capability to understand litthe English command. Their problem is how to design an RC filtered power supply that can be used in their prototype AI robot which has a load range of 250 ohms to 1.25 kilo-ohms and since this is just a prototype it must be wired to the 240V 60Hz peak AC supply in their laboratory. They ask the VoltageMaker Company to ship them 20 pcs of 12V DC power supply and it must be included in the data sheet of load current in rms and peak, the PIV, the power range absorbed by the load, the ratio of the transformer, and the secondary rms voltage of the power supply. The power supply must be in a bridge type. Considering that you are a member of that team, what is your design? please answer or draw it clearly with labels. Thank you. this…
Design a combinational circuit with four inputs – A, B, C, and D – and one output, F. F is to be equal to 1 when A = 1, provided that B = 0, or when B = 1, provided that either C or D is also equal to 0.