Q2/ The rigid platform in Figure below has negligible mass and rests on two steel bars, each 250 mm long. The center bar is aluminum and 249.9 mm long. Compute the stress in the aluminum bar after the center load P = 400 kN has been applied. For each steel bar, the area is 1200 mm? and E = 200 GPa. For the aluminum bar, the area is 2400 mm? and E = 70 GPa. P Steel Aluminum Steel

Q2/ The rigid platform in Figure below has negligible mass and rests on two steel bars, each 250 mm long. The center bar is aluminum and 249.9 mm long. Compute the stress in the aluminum bar after the center load P = 400 kN has been applied. For each steel bar, the area is 1200 mm? and E = 200 GPa. For the aluminum bar, the area is 2400 mm? and E = 70 GPa. P Steel Aluminum Steel

Name: Q2/ The rigid platform in Figure below has negligible mass and rests
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2/ The rigid platform in Figure below has negligible mass and rests on two steel bars,each 250 mm long. The center bar is aluminum and 249.9 mm long. Compute thestress in the aluminum bar after the center load P = 400 kN has been applied. Foreach s

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.29P: A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see...

See similar textbooks

Similar questions

A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see figure), where s = 12.5 in. The height of the post L is measured from the base to the centroid of the sign. The stop sign is subjected to wind pressure p = 20 lb/ft2 normal to its surface. Assume that the post is fixed at its base. What is the resultant load on the sign? (Sec Appendix E, Case 25, for properties of an octagon, n =8.) What is the maximum bending stress in the post? Repeat part (b) if the circular cut-outs arc eliminated over the height of the post.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and tube are compressed between the rigid plates of a testing machine which applies forces P. Calculate the allowable value of the compressive force if the yield stresses of sleel and aluminum are srs = 50 Ksi and ??A= 60 ksi, respectively. Assume that As= 12 in2. AA= 6 in2. L = 20 in., Es= 29,000 tsi and EA=10,600 ksi
A hollow circular pipe (see figure} support s a load P that is uniformly distributed around a cap plate at the top of the lower pipe. The inner and outer diameters of the upper and lower parts of the pipe are d1= 50 mm, d2= 60 mm, rf3 = 57 mm, and d1= 64 mm, respectively. Pipe lengths are Lt= 2 m and L, = 3 m. Neglect the self-weight of the pipes. Assume that cap plate thickness is small compared to I, and E,. Let E = 110 MPa. (a) If the tensile stress in the upper part is d = 10.5 MPa. what is load PI Also, what are reactions ft, at the upper support and R-, at the lower support? What is the stress ar(MPa) in the lower part? (b) Find displacement S(mm) at the cap plate. Plot the axial force diagram (AFD) [Ar(.f)] and axial displacement diagram (ADD)[5(.t)]. (c) Add the uniformly distributed load q along the censorial axis of pipe segment 2. Find q (kN/m) so that It, = 0. Assume that load P from part (a) is also applied.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
QZ/ The rigid platform in Figure below has negligible mass and rests on two steel bars, each 250 mm long. The center bar is aluminum and 249.9 mm long. Compute the stress in the aluminum bar after the center load P = 400 kN has been applied. For each steel bar, the area is 1200 mm® and E = 200 GPa. For the aluminum bar, the area is 2400 mm’ and E = 70 GPa.
The Figure shows a bar AB, of length L, which is supported at point A, against the wall andsuspended by a cable at point B, and a weight w is hung from it at end B. The weight of thebar AB and cable weight are negligible. Suppose the weight W and the angles θ1 and θ2are known. What is the direction of the reaction force R of the wall against the bar
the bent bar AB weighing 10lb/ft is mounted as shown in figure 2 upon a carriage weighing 250 lb. The center of gravity of the carriage is at C midway between the wheels. If P=108lb and there is no frictional resistance at the wheels, find the wheel reaction R1. find the vertical component of the hinge force at A. find the horizontal concept of the hinge force at A.
4. A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25° angle with the crane (see figure below). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 mfrom the upper end of the crane. When the crane is raised to 55° above the horizontal holding an 11,000N pallet of bricks by a 2.2 m, very light cord, find (a) the tension in the cable and (b) the horizontal andvertical components of the force that the axle exerts on the crane.
the slender plank shown in figure is held in equilibrium by the action of the force Fp. find the magnitude of Fp if the mass of the plank is 200 kg. assume all surfaces are frictionless