Q2: Tow anti parallel thyristors (Triac) supply a load resistive load with R=10 2 from a source with sinusoidal Waveform of peak value of 300V. a) Determine the output voltage if the firing angle a = 30°, a = 90°, a = 120° and discus results of (a) by your own words. b) Source power factor for each value of a in (a). c) RMS current of one SCR if a = 30°.

Q2: Tow anti parallel thyristors (Triac) supply a load resistive load with R=10 2 from a source with sinusoidal Waveform of peak value of 300V. a) Determine the output voltage if the firing angle a = 30°, a = 90°, a = 120° and discus results of (a) by your own words. b) Source power factor for each value of a in (a). c) RMS current of one SCR if a = 30°.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given the following details: The inverting adder schematic as seen below Vac is an AC voltage source which generates a sine waveform with amplitude 1mV and frequency 1kHz Vout is a sine waveform with amplitude 1V and has a DC offset of 3.5V Find the values of Vdc, R1, R2 and Rf that would satisfy the description for Vout. Assume ideal scenario (i.e. do theoretical computations instead of practical simulations)
1) The current and voltage waveforms given in the figure on the right.power electronics converter to which the shapes belongDraw the circuit. The stress on the load andThe relations for the average value of the current are obtained.please. 2) Positive half wave of AA voltage transferred to the loadfixed negative half wave is a controllableDraw an AA phase control circuit. Pure ohmic load and ?output current and voltage for a trigger angle such asGive the waveforms. 0 <? <pi
Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two approaches
amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81
Two SCRs are used in a midpoint converter arrangement. The source RMS voltage is230 V, and the frequency is 50 Hz. The load is 100 mH inductor in series with 2 .The input lines have series inductance 50 H. (a) For a phase delay of 45, plot the voltage waveform measured at the output of the midpoint converter. (b) What is the output power for 45 delay?
A load resistor RL is in parallel with a noisy source (vS << VS), and a biasing component, which canbe a linear or a nonlinear element. Suppose we can write the total source voltage vS and the totalload voltage vL as shown in the image. Answer the ff and explain clearly. i. Let the biasing component be a linear resistor with resistance RB. Without the noise, determinethe value of RB so that the load voltage is 5V. ii. With the noise, determine the ratio of the load voltage noise and the source noise (vI /vS )..
A highly inductive load, such that load current can be assumed constant, is to be supplied from a 230 V, 50 Hz, single-phase supply by a fully-controlled and a halfcontrolled bridge. Compare the average load. Voltage provided by each bridge at firing angles of 30° and 90°. Neglect device voltage drops.
a) Demonstrate input and output waveform of single phase Cyclo-converter such that output frequency is 1/3 of input supply frequency with circuit diagram. b) Perform the calculation to analyze (i) output RMS voltage and (ii) input power factor of single-phase AC voltage controller as shown in the following figure. Suppose converter has a resistive load of R=‘A’ Ohm and the input voltage is Vs=220, 50Hz with a delay angle of π/3. A= 4
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed to be (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.
The average value of the output voltage with PWM is Vo = 5 V. If the on state duration Ton is 5 µs and supply voltage Vin = 20 V, find the duty ratio d, switching period Ts and switching frequency fs of the system. Draw the waveforms for Vin and Vo voltages stating on and off durations.
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is 33 V