The circuit below shows a reactor being disconnected from its supply. During the process of opening, the circuit breaker reignites but interrupts the reignition current at the first zero of the high frequency current, trapping energy in L2 Compute the peak voltage subsequently appearing across the reactor as a conseguence of this trapping of energy. L1 = 15mH L2 = 352mH 2nF Vs = 138/1.732 kV св L, Vs

The circuit below shows a reactor being disconnected from its supply. During the process of opening, the circuit breaker reignites but interrupts the reignition current at the first zero of the high frequency current, trapping energy in L2 Compute the peak voltage subsequently appearing across the reactor as a conseguence of this trapping of energy. L1 = 15mH L2 = 352mH 2nF Vs = 138/1.732 kV св L, Vs

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
Please provide Handwritten answer. Question: Note: in all the questions there is a variable X X=103 Q4.For the following electric circuit, design a close loop state space system using the pole placement technique which tracks a unit step input. The desired roots in complex plane should be place in such a way that the system achieves minimum settling time having undamped natural frequency equal to 4. The state variables are voltage across capacitor (also the output) and current through inductor.
A coil of wire (N = 70) carries a current of 3A and has a radius of 8cm. The current is decreased at 0.3 A/s. Inside this coil is another coil of wire (N = 10 and r = 3 cm) aligned so that the faces are parallel. What is the average emf induced in the smaller coil during 6s?
A circuit consisting of 20 ohm resistance in series with a coil having 8 ohm resistance and 0.16 inductance is connected to a 220-volt, 50-hertz source. Determine the voltage drop across the coil.
Enumerate five step-by-step procedures of Norton’s theorem method in application to electric circuit problem solution or analysis.
GENERAL RLC CIRCUITS: Solve and show your solution completely. Make sure your answers are in 4 decimals places. An impedance coil takes 10 A and absorbs 250 W when connected across a 220-V, 60-Hzsource. What power will it absorb when connected across a 110-V, 25-Hz mains?
An industrial coil has a resistance of 35 ohms and a reactance of positive 3 (x + y) ohms and rated values 440 volts at 60 Hz. A factory will connect the coil to a 440 volts, 50 Hz supply. Solve for the value of a series resistor needed to avoid overcurrent condition if
A coil of inductance 50 mH and resistance 5 ohm is connected to a 110V, d.c. supply. Determine the final value of current, the value of current after 4 ms, the value of the voltage across the resistor after 6 ms, the value of the voltage across the inductance after 6 ms, and the time when the current reaches 15A.
What size ungrounded conductors do we need for the 60 amp load? All conductors have typeTHHN insulation.
In the workshop, when manufacturing an inductor, a technician winds 100 turns of a fine conductor onto a large iron ring and leaves it ready for testing. The next day, another technician comes and inadvertently coils 100 more laps with another fine conductor in the opposite direction. Thinking of having two identical coils in parallel, they connect the terminals of the two in parallel and feed both with the same source. If the same current, I0, flows through the two coils, and we draw an Ampere loop through the center of the ring. Choose the one from the following options. Select one: a. The net current within the Ampere loop is 100 I0 . b. The net current within the Ampere loop is zero. c. The magnetic flux in the ring is going to be twice that of a single coil. d. The net current within the Ampere loop is 200 I0 . show solving steps!!!