Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static load to the plates is 120 kN. The permissible ultimate and yield stresses are 640 MPa and 390 MPa respectively, find the length of weld when (a) a double transverse welds (b) a double parallel fillet welds are used, use factor of safety (2).

Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static load to the plates is 120 kN. The permissible ultimate and yield stresses are 640 MPa and 390 MPa respectively, find the length of weld when (a) a double transverse welds (b) a double parallel fillet welds are used, use factor of safety (2).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
A steel plate, 80 mm wide and 10 mm thick, is joined toanother steel plate by means of a single transverse anddouble parallel fillet welds, as shown in figure. The strengthof the welded joint should be equal to the strength of theplates to be joined. The permissible tensile and shearstresses for the weld material and the plates are 100 and 70N/mm2 respectively. Find the length of each parallel filletweld. Assume that the tensile force passes through the centre of gravity of three welds.
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
A rectangular steel plate is welded as a cantilever to a vertical column and supports a single concentrated load P. Determine the weld size if shear stress in the same is not to exceed 140 MPa
A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds at the ends. If the plates are subjected to a load of 70 kN, find the size of weld for static load The permissible tensile stress should not exceed 70 MPa.
A tension plate shown below is used to support suspended load "T". Gusset Plate F, = 248 MPa Fu = 400 MPa 200 mm. Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory)
a. figure 1 shows a large pressure vessel fabricated by welding together steel plates of 12 mm thickness as shown. If the stress acting normal to the welds must be less than 80 MPa, what is the largest allowable internal pressure? b. determine the state of strain in the tank when the internal pressure is 0.3 MPa. The elastic modulus (?) of the steel is 200 GPa, and the Poisson’s ratio (?) is 0.3. c. The welded joints are to be replaced with equally spaced rivets (loaded in single shear), each with a diameter of 10 mm and maximum allowable stress of 80 MPa. For an internal pressure of 0.3 MPa inside the tank, determine: (i) The minimum rivet spacing (?) along the circumference of the tank. (ii) The minimum rivet spacing (?) along the height of the tank. d. If the pressure vessel is subjected to a temperature change of 50°C determine the change in height. The co-efficient of thermal expansion for steel can be taken as ? = 11.2 × 10−6 °C−1.
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
A plate 70mm wide and 15mm thick is joined with another plate by a single transverse weld and a double parallel fillet weld. The maximum tensile and shear stresses are 60MPa and 50MPa respectively. Find the length of each parallel fillet weld, if the joint is subjected to static loading.
A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand safely a working pressure of 0.86 MPa. Boiler plate with an allowable tensile stress of 76 MPa. All seams will be butt welds with an expected efficiency of 100 percent. a.) Determine the force per lineal mm of longitudinal seam, b.) Determine the required thickness “t” of wall, c.) Determine the unit stress in the circumferential seam.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.