Q2. Calculate the slope and deflection of a SSB with span 5m carrying a point load of 20kN at 2m from the right support and carries a udl of 5kN/m over an entire span. Use E = 10x10^3 N/mm2 and the beam section is 300 x 450mm in C/S. Also, if the Deflection is restricted not to exceed 10mm and only a udl is acting on it of 9000N/m over the entire span. Calculate the rectangular beam dimensions with similar configuration as before and a permissible stress of

Q2. Calculate the slope and deflection of a SSB with span 5m carrying a point load of 20kN at 2m from the right support and carries a udl of 5kN/m over an entire span. Use E = 10x10^3 N/mm2 and the beam section is 300 x 450mm in C/S. Also, if the Deflection is restricted not to exceed 10mm and only a udl is acting on it of 9000N/m over the entire span. Calculate the rectangular beam dimensions with similar configuration as before and a permissible stress of

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Since the load state and the rectangular cross section of the horizontal beam element are 200 MPa, the shear stress value is 200 MPa;What is the safety beam section (bx2b) value?
Compute the slope and deflection of the simply supported beam shown in figure Q2a. Assume value of E = 29 × 106 psi and I = 22.4 in4.
For the beam and loading shown, use discontinuity functions to compute(a) the slope of the beam at C (positive if counterclockwise and negative if clockwise).(b) the deflection of the beam at C.Assume LAB = 210 mm, LBC = 140 mm, LCD = 120 mm, LDE = 260 mm, MB = 200 N-m, P = 1080 N and a constant value of EI = 590 × 106 N-mm2 for the beam.
Uniformly distributed load on a simple support beam with a length of 6 metersMaximum that occurs on the cross section when q is appliedIf bending stress is 337.5MPa,How many kN/m is the equal distribution load q?(However, the cross section of the beam is wide x height = 40mm x)100 mm.)
A cantilever beam having a span L of 6.0 m carries a concentrated load P=71kN, at midspan, E = 200,000 N/mm2 and Ixx = 60 x 106 mm4. Compute the end of the slope at the end of the beam using moment-area method. Show complete solution.
A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2,I = 200 x 106mm4.
A simply supported beam of length 5m, with a hollow rectangular cross-section outer width of 45mm x outer depth of 90mm and the overall wall thickness of 10 mm which is subjected to a mid-point load of 450 kN, a UDL of 4 kN/m is acting for the entire span. Find the maximum deflection at mid-span and Maximum bending Moment in the beam. Take Young's modulus as 105 GPa.
Compute the initial deflection of the beam at midspan under service loads with the following specifications: f'c = 4000 psi, 36-inch height, depth of rebar assumed to be 3 inches less than the height, 16-inch width, 4 #9 bars (tension), Grade 60 rebar, 30' clear spans, service loads of: DL = 0.25k/ft, LL = 1.2k/ft. The DL does NOT include self-weight of the beam or of the precast concrete deck planks that have a weight of 60 PSF. The beam picks up a tributary width of 12 feet. Also, note that this beam is continuous and is the middle beam of 5 equal spans. Check the initial deflections against the ACI deflection requirements. Then calculate the long-term deflections and check those against the ACI requirements. For both situations, assume that finish materials will be attached to the beam. Last: Instead of performing a structural analysis to determine the maximum deflection in the beam, conservatively figure that the maximum deflection will be 60% of what it would have been for a…
Calculate the maximum def lection δmaxof a uniformly loaded simple beam if the spanlength L = 2.0 m, the intensity of the uniform loadq =2.0 kN/m, and the maximum bending stressσ = 60 MPa.The cross section of the beam is square, and thematerial is aluminum having modulus of elasticityE = 70 GPa.
Problem 4 For the beam shown below, find the value of EIY at 2m from R2. E= 18500MPa and; beam cross -section=200mmX275mm . Use Area-moment method w=15kN/m
a concentrated load p= 45200 N is applied at the of a fixed beam of length 1.54m depth 112mm width 96mm. calculate the deflection
A cantilever beam has a length L =12 ft anda rectangular cross section (b = 16 in., h = 24 in.). Alinearly varying distributed load with peak intensityq0 acts on the beam.(a) Find peak intensity q0 if the deflection at joint Bis known to be 0.18 in. Assume that modulusE = 30,000 ksi.(b) Find the location and magnitude of the maximumrotation of the beam.