Q22)ii) In Al-Ahmadi distribution station, a voltmeter of range (0-300V) and ammeter of range (0-10A) are used to measure a line voltage of 33kV and current of 1000A. On a particular day the voltmeter and ammeter shows a voltage of 155V and current of 4A respectively, then estimate the following. (Use sample values for winding turns) i. Total (Actual) line Voltage in the substation ii. Total current in the substation

Q22)ii) In Al-Ahmadi distribution station, a voltmeter of range (0-300V) and ammeter of range (0-10A) are used to measure a line voltage of 33kV and current of 1000A. On a particular day the voltmeter and ammeter shows a voltage of 155V and current of 4A respectively, then estimate the following. (Use sample values for winding turns) i. Total (Actual) line Voltage in the substation ii. Total current in the substation

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.62P: Rework Example 3.12 for a+10 tap, providing a 10 increase for the high-voltage winding.

See similar textbooks

Similar questions

An electrical lineman is connecting three single-phase transformers in a Y(primary)-Y(secondary) configuration, for power service to a business. Draw the connecting wires necessary between the transformer windings, and between the transformer terminals and the lines: Note: fuses have been omitted from this illustration, for simplicity.
A three phase, three wire short transmission line has a resistance of 3 ohms and a reactance of 8 ohms per wire. At the receiving end, a balanced 3-phase load draws a line current of 60 A at 13,500 volts line to line, 0.90 pf lagging. Assuming the receiving end voltage is maintained at 13,500 V, solve the size in kVAR of capacitors needed to raise the power factor at the receiving end to 0.95 leading. Ans. 73.28 kVAR
The single line diagram of a power system is shown below. Load represented as impedance, (13.2) kV voltage It draws 60 MVA power from the system when it is below and (0.9) back power factor. Generators and transformers The related electrical parameters are given below. According to this; a) Calculate all impedances in this given circuit in pu and draw the equivalent impedance diagram of the circuit. (Select the base values as 100 MVA and 13.8 kV.) b) Since the voltage values of the generators are given as E1=1.1∟0° pu and E2=1.25∟10° pu, Calculate the value of the voltage (V1).
2. How two identical single phase transformers each of rating 5kVA, 200V/100V, 50Hz be used to stepdown a balanced 3-phase, 200V supply to a balanced 3-phase, 100V supply? Explain with circuit andphasor diagrams. Calculate also the maximum kVA that can be supplied from this connection.
Three phase 300KVA, 480V / 4170V distribution transformer workbench, 300KVA to a three-phase load connected to the secondere references, Calculate the desired by assuming that the transformer bank is connected to a triangle-star (Δ-Y). a)Find kVA rated power per phase. b)Calculate primary and secondary rated current and voltage values. c)calculate the ratio of the number of winding.
For the Δ - Δ circuit, calculate thephase and line currents.
The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformertested at 50 Hz:Voltage (V) Current (A) Power (kW)LV winding with HV terminals open-circuited: 3810 9.86 8.14HV winding with LV terminals short-circuited: 920 141 10.3a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltagewinding.b. Calculate the cantilever equivalent-circuit parameters as referred to the transformer low-voltagewinding.c. With the transformer carrying rated load and rated voltage at its low-voltage terminal, calculate thepower dissipated in the transformer.d. Repeat part a and b in per-unit. Compare and comment on your result.
A 2-phase, 3-wire a.c. sistem has a middle conductor of same cross-sectional area as the outer and supplies-load of 20MW. The system is converted into 3 phase , 4-wire system by running a neutral wire . Calculate the new power which can be suppliad if voltage across consumer terminals and percentage line loses remain the same . Assume balanced load
Draw the single line diagram of a substation having the following equipments: i) Incoming lines: Two, 132kV ii) Outgoing lines: (a) Five, 132kV (b) Five, 33kV iii) Transformers: (a) One, 25MVA, 132/33kV, D/Y (b) One, 2MVA, 33kV/ 420V,Y/Y iv) Bus-bars: 132 kV-Duplicate bus-bar, 33kV single bus-bar Show the positions of necessary equipments that using for protections, measurements and
Question 2The electrical power supply system of a particular country is made of the following. Draw a single line diagram of the electrical power supply system of the country based on the information below using any computer-aided software. Power supply from an infinite bus bar S connected to bus bar A, through a circuit breaker connected between isolators and a three-phase delta/star solidly earthed transformer T1.Power supply source from a generator G1 connected to bus bar B through a circuit breaker connected between isolators, and a three- phase delta/star solidly earthed transformer T2. power supply sources from two generators G2 and G3. Each of the generators are connected to a reactor. Furthermore, each of the generators connected to a common bus bar C through a circuit breaker connected between isolators and a three-phase star/star solidly earthed transformer T3 and T4 respectively. bus bar F to bus bar A by means of two isolators, one at each end of transmission line L6; bus…
Draw the single line diagram of a substation having the following equipments:i) Incoming lines: Two, 132kVii) Outgoing lines: (a) Five, 132kV (b) Five, 33kViii) Transformers: (a) One, 25MVA, 132/33kV, D/Y (b) One, 2MVA, 33kV/ 420V,Y/Yiv) Bus-bars: 132 kV-Duplicate bus-bar, 33kV single bus-barShow the positions of necessary equipments that using for protections, measurements and communications.
Rework Example 3.12 for a+10 tap, providing a 10 increase for the high-voltage winding.