ı sent this page but you solved just 1a 1b 1c where is the 2a 2b 2c and third questions? Please solve others. QUESTIONS:1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred toLV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When ratedcurrent is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A.a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging.b. Find the efficiency of this transformer at full load, 0.8 power factor lagging.c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measuredvalues of these tests?2. The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformertested at 50 Hz:Voltage (V) Current (A) Power (kW)LV winding with HV terminals open-circuited:38109.868.14HV winding with LV terminals short-circuited:92014110.3a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltagewinding.b. Calculate the cantilever equivalent-circuit parameters as referred to the transformer low-voltagewinding.c. With the transformer carrying rated load and rated voltage at its low-voltage terminal, calculate thepower dissipated in the transformer.d. Repeat part a and b in per-unit. Compare and comment on your result.3. A three-phase Y-Y transformer is rated at 25 MVA, 13.8-kV:69-kV and has a single-phaseequivalent series impedance 62 + j388 mN referred to the low-voltage winding.a. A three-phase short circuit is applied to the low-voltage winding. Calculate the voltage applied to thehigh-voltage winding which will result in rated current into the short circuit.b. The short circuit is removed and a three-phase load is connected to the low-voltage winding. Withrated voltage applied to the high-voltage winding, the input power to the transformer is observed tobe 18 MW at 0.75 power-factor lagging. Calculate the line-line terminal voltage at the load.4. A 45-kVA, 120-V:280-V single-phase transformer is to be connected as a 280-V:400-Vautotransformer. Determine the voltage ratings of the high- and low-voltage windings for thisconnection and the kVA rating of the autotransformer connection.

Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV tested at 50 Hz: Voltage (V) Current winding with HV terminals open-circuited: 3810 9.86 winding with LV terminals short-circuited: 920 141 Calculate the cantilever equivalent-circuit parameters as referred to the tra winding. Calculate the cantilever equivalent-circuit parameters as referred to the tra winding.

The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV tested at 50 Hz: Voltage (V) Current winding with HV terminals open-circuited: 3810 9.86 winding with LV terminals short-circuited: 920 141 Calculate the cantilever equivalent-circuit parameters as referred to the tra winding. Calculate the cantilever equivalent-circuit parameters as referred to the tra winding.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.14P: A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Similar questions

For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?