Q3/ For the figure shown pin C, is constrained to move in the circular slot AB of radius r= 70 mm. At t = 0 the pin starts from rest and moves with speed increases at a constant rate of 13 mm/s?. (a)/ the velocity when t= 5 s is : B D O 61 mm/s O 66.23 mm/s 64.5 mm/s 65 mm/s O 60.37 mm/s

Q3/ For the figure shown pin C, is constrained to move in the circular slot AB of radius r= 70 mm. At t = 0 the pin starts from rest and moves with speed increases at a constant rate of 13 mm/s?. (a)/ the velocity when t= 5 s is : B D O 61 mm/s O 66.23 mm/s 64.5 mm/s 65 mm/s O 60.37 mm/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A disk is attached by a spring to a pin. The disk can roll in the horizontal direction and the pin is above it. The spring has an unstretched length of .5m and a spring modulus of 600 N/m THe disk has a mass of 20kg and a radius of 200mm The center of hte disk is 600mm below the pin and 320mm to the side (so the spring starts diagonal) If the spring is released, what is the speed of the disk when the spring is perfectly vertical? Assume the disk does not slip and is free to spin
Machine Dynamics: In the mechanism in the figure; The 2nd limb in the horizontal position rotates with a constant angular velocity of 100 rad/s under the effect of external torque T12.Obtain the equations of change of axial internal force, shear force and bending moment in limb 3 due to inertia and bond forces at the specified position, ignoring frictions.(O2 joint point is the center of gravity of limb 2) "Detailed Solution Please"
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
A motor is attached to a pulley of radius 10 cm and mass 1 kg. A belt passes through the pulley that connects to a hollow sphere with a radius of 40 cm and a mass of 2 kg (see figure below). If the final speed of the first round, the angular speed of the SPHERE is 3πrad/s:a) What is the final energy consumption of the motor? b) If the torque is constant, what is the magnitude of the motor's torque? that there is no friction in the axes of the sphere and that all energy consumed by the motor is transformed into work.
A single cylinder reciprocating engine has speeded 300 RPM. Stroke 250 mm, mass of reciprocating parts 50 kg. Mass of revolving parts at 150 mm radius 37 kg. If two fourth of the reciprocating parts and all the revolving parts are to be balanced, find (i) The balance mass required at 400 mm radius (ii) The residual unbalanced force when the crank has rotated 45° TDC.
(3) A pendulum consisting of a rod of mass 2m of mass 3kg and a ball of mass 1kg and a radius of 0.3m attached to one of the bar length. The axis of rotation as shown in the figure below What is the angular velocity of the pendulum at its lowest point if it is released from Rest at an angle of 30?
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
Q3/ A vertical double acting steam engine develops 80 kW at 240 rpm. The maximum fluctuation of energy is 25% of the work done per stroke. The maximum and minimum speeds are not to vary more than +1% of the mean speed. Find the mass of the flywheel, if the radius of gyration is 0.65 m.
Three bars, each 2 ft long and weighing 9.66 lb, are pinned together toform the equilateral frame shown in Fig. P-1245. They rotate in a horizontalplane about a vertical axis at A. What torque is required to cause an angularacceleration of 12 rad per sec? What is the reaction at A when the framereaches a speed of 38.2 rpm?
A disk is attached by a spring to a pin. The disk can roll in the horizontal direction and the pin is above it. The spring has an unstretched length of 0.5 m and a spring modulus of 600 N/m. The disk has a mass of 20 kg and a radius of 200 mm. The center of the desk is 600 mm below the pin and 320 mm to the side (So the spring starts diagonal). If the spring is released, WHAT IS THE SPEED OF THE DISK WHEN THE SPRING IS PERFECTLY VERTICAL? Assume the disk does NOT slip and is free to spin.
The plumb line of a 2m pendulum describes an arc of a circle in a vertical plane. If the tension in the string is 2.5 times the weight of the bob for the position shown in the figure, find the velocity and acceleration of the bob at that position.
The beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. What is the magnitude, in newtons, of the tension in the cable? e. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables…