i need the answer quickly Q3: The web of a girder of I-section is 45 cm deep and1 cm thick; the flanges are each 22.5 cm wide by 1.25em thick. The girder at some particular section has towithstand a total shearing force of 200 kN. Calculatethe shearing stresses at the top and middle of the web.125m

Answered: Image /qna-images/answer/c50919b3-0483-4a2b-bac2-51da549f0d6a.jpg

Answered: Q3: The web of a girder of I-section is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ship's propeller shaft is 5 inches in diameter. The thrust load is 12,000 lb and the torque is 150,000 in - lb. Determine the resultant maximum shearing and compressive ( tensile ) stresses.
A steel shaft with a diameter of 40 mm and the length of 1.1 m transmits 60 hp from an electric motor to a compressor. If the allowable shear stress is 50 MPa and the allowable angle of twist is 1.50, what is the minimum allowable speed of rotation.
A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?
In a pipe of diameter 100 mm, carrying water, the velocities at the pipe center and 30 mm from the pipe center are found to be 2.5 m/s and 2.2 m/s respectively. Find the wall shearing stress.
An aluminum thin‐walled tube of hollow rectangular cross‐section, Figure 1,is subjected to a torque of magnitude, T = 15360 N.m. If the tube lengthis, L = 1 m , and the shear modulus of aluminum is, G = 28 GPa.1. Determine the total angle of twist of the one‐meter long tube.2. Determine the shear stresses on the walls of the tube cross‐section.Where does the maximum shear stress occur?
A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the shaft material is 56 N/mm2. Determine the diameter of the shaft?
In the figure, a double shear occurs at 20mm diameter pin at B, what is the shearingstress? In the figure, if the thickness of member AB is 15mm, what will be the value of itsbearing stress?
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate.
A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress of 60 MPa. What is the diameter of the solid steel shaft? Use G = 83 GPa.
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
2. A rectangular key was used in a pulley connected to a line shaft at 23 HP and 10 rps. If shearing of key is 230 Mpa, determine the force acting on key length if key width is one-fourth of shaft diameter and key length of one inch.
A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the shaft must be limited to 72 MPa, determine the minimum diameter d required for a solid shaft.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q3: The web of a girder of I-section is 45 cm deep and I cm thick; the flanges are each 22.5 cm wide by 1.25 cm thick. The girder at some particular section has to withstand a total shearing force of 200 kN. Calculate the shearing stresses at the top and middle of the web.