q3..Shaft a transmits 7 hp. Determine the reaction a bearings A and C knowing that these bearings will support thrust loading. The helical gears have 17.5° normal pressure angle and 25° helix angle and 14 normal diametral pitch. Dimensions in

q3..Shaft a transmits 7 hp. Determine the reaction a bearings A and C knowing that these bearings will support thrust loading. The helical gears have 17.5° normal pressure angle and 25° helix angle and 14 normal diametral pitch. Dimensions in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.
A parallel-shaft gearset consists of an 18-tooth helical pinion driving a 32-tooth gear. The pinion has a left-hand helix angle of 20, a normal pressure angle of 25, and a normal module of 3 mm. Evaluate root diameter (mm) of the pinion. A) 51,21 B) 49,92 C) 50,00 D) 48,00 E) 52,08
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
in the epicyclic gear, annulus gear B has 120 teeth externally and 100 teeth internally. driver A has 20 teeth and the arms E is connected to the driven shaft. The Sun gear D has 60 teeth. If A revolves at 100 r.p.m clockwise and D revolves at 27 r.p.m clockwise. If gear D is fixed and A transmits a torque of 10 N.m at 100 r.p.m clockwise
The approximate distance between the two parallel shafts is 1500 mm. The shafts are to be connected by spur gearing. If one shaft runs at 1500 r.p.m. and the other at 2500 r.p.m., Design the gears, if the module is 7 mm. (
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. Theaddendum length is 5 mm and the module is 5.5 mm. If smaller wheel is the driver androtates at 1500 r.p.m. find the velocity of sliding at the point of engagement and at thepoint of disengagement.
a pinion has 56.716 teeth of 5.96mm module and runs at 2.265 rev/min with a torque of 39.961N.m. it meshes with a gear wheel which has 124.409 teeth. the gears operate with a pressure angle of 27.61 degrees and a contact ratio of 31.22. If the path of recess is 1.2 times the path of approach, determine the path of recess
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?