3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW, respectively. If the shaft is made of steel with the allowable shear stress of 80 MPa, and the relative angle of twist between any two gears cannot exceed 0.065 rad, determine the required minimum dilameter d of the shaft to the nearest millimeter. The shaft is rotating at 800 rpm. 600 mm 600 mm 600 mm

3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW, respectively. If the shaft is made of steel with the allowable shear stress of 80 MPa, and the relative angle of twist between any two gears cannot exceed 0.065 rad, determine the required minimum dilameter d of the shaft to the nearest millimeter. The shaft is rotating at 800 rpm. 600 mm 600 mm 600 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 60-mm-diameter shaft is made of 6061-T6 aluminum. If the allowable shear stress is tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.06 rad, determine the maximum allowable torque T.
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
The steel shaft DF consists of three concentric tubes and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 15 kW of power to the shaft while it is running at 55 rev/ sec. The gears A, B, and C remove 4 kW, 5 kW, and 6 kW, respectively. The shaft is free to turn in its support bearings D and F. Determine the shearing stress developed in segments BC and CE
Determine a.) the maximum torsional stress, τmax, and b.) the maximum angle of twist, φ, of the solid shaft if the shaft has a diameter of d = 50 mm and the shear modulus is G = 75 GPa.
A circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm.
The gear motor can develop 1 10 hp when it turns at 80 rev>min. If the allowable shear stress for the shaft is tallow = 4 ksi, determine the smallest diameter of the shaft to the nearest 1 8 in. that can be used.
The motor delivers 50 hp while turning at a constant rate of 1350 rpm at A. Using the belt and pulley system this loading is delivered to the steel blower shaft BC. Determine to the nearest 1 8 in. the smallest diameter of this shaft if the allowable shear stress for steel is tallow = 12 ksi.
A flange coupling is to be designed, using 6 bolts at a distance of 149mm from thecenter of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is totransmit 5485 hp at a speed of 1200 rpm, (a) determine the bolt diameter required inmm. (b) If the shaft is made of the same material as the bolt, determine the requireddiameter of the shaft in mm.
Determine the smallest safe diameter of the solid steel shaft if the maximum shear stress is 50,000 KPa(kN/m2) and the angle of twist is limited to 0.15 radian in a length of 4m. Use G = 83 GPa. The shaft transmits 30 kW of power at 2 Hz caused by torque.
The shaft is made of A992 steel with the allowable shear stress of tallow = 75 MPa. If gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively, determine the required minimum diameterd of the shaft to the nearest millimeter. Also, find the corresponding angle of twist of gear A relative to gear D. The shaft is rotating at 600 rpm.
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72 MPa. the shaft is operating at an angular velocity of 1700 rev/min. Take ci= 0.75 co. A) If the motor is to deliver a power of 25 kW, determine the required minimum outer diameter of the tubular shaft to the nearest mm. B)Determine the required corresponding inner diameter of the tubular shaft to the nearest mm.