Q3b. The stress-strain characteristic curves for materials A, B and C are shown below. Which one statement most accurately describes therelative toughness and ductility for materials A, B & C?Material AMaterial BMaterial CStrainSelect one:a. Material A has low toughness, Material B has high ductility and Material C has low toughness.b. Material A has high toughness, Material B has low ductility and Material C has low toughness.c. Material A has low ductility, Material B has low toughness and Material C has low toughness.d. Material A has high ductility, Material B has low toughness and Material C has high toughness.Stress

Given stress strain curve. The properties are At point A : High strength Low ductility Low…

Q3b. The stress-strain characteristic curves for materials A, B and C are shown below. Which one statement most accurately describes the relative toughness and ductility for materials A, B & C? Material A Material B Material C Strain Select one: O a. Material A has low toughness, Material B has high ductility and Material C has low toughness. O b. Material A has high toughness, Material B has low ductility and Material C has low toughness. O c. Material A has low ductility, Material B has low toughness and Material C has low toughness. O d. Material A has high ductility, Material B has low toughness and Material C has high toughness. Stress

Q3b. The stress-strain characteristic curves for materials A, B and C are shown below. Which one statement most accurately describes the relative toughness and ductility for materials A, B & C? Material A Material B Material C Strain Select one: O a. Material A has low toughness, Material B has high ductility and Material C has low toughness. O b. Material A has high toughness, Material B has low ductility and Material C has low toughness. O c. Material A has low ductility, Material B has low toughness and Material C has low toughness. O d. Material A has high ductility, Material B has low toughness and Material C has high toughness. Stress

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
A material has the following properties, ultimate Sul = σul = 350mpa, the strain hardening exponent n=0.20. Determine the value for the strength coefficient K.
a) Compression tests are generally performed on brittle materials-why?b) How a cast iron specimen fails under compression load?c) Define secant modulus?
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
1. A circular rod of diameter 20mm and 500mm long is subjected to atensile force 50kN. The modulus elasticity for steel may be taken as 200kN/??2. Find stress and strain due to applied load.
The assembly shown consists of an aluminum shell (Ea = 70 GPa, αa = 23.6 × 10−6/°C) fully bonded to a steel core (Es = 200 GPa, αs = 11.7 × 10−6/°C) and the assembly is unstressed at a temperature of 20°C. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches 185°C. The stress in the aluminum is − _____ MPa.
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
Drive the relation of stress transformation.
A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induce A. no stress B. shear stress C. tensile stress D. compressive stress
Q5. A material is made in circular rod form of diameter 1.5 cm and 200mm long. It is fixed on the Universal Testing Machine. When SKN force is applied on the material, its length became 201.5 mm, material shows maximum stress 550MPa. Find [3] (1) Stress (ii) Youngs modulus (iii) Max force
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the propotional limit, modulus of elasticity (i.e the slope of the initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percent reduction area. TENSILE-TEST DATA Load(kN) Elongation(mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture