Q4) (25 p)Two objects with masses MA 1 Kg. and Ma 4 are placed on the side surfaces of inclined planes as shown in the figure, where right side is frictionless. They are connected to each other with a rope passing through a pulley with radius R and moment of inertia I. The kinetic friction coefficient on left side is H = 0.01, If the system is moving to right with an acceleration a = 4 m/s. (Both inclined planes have 45°) a) (5 Pts.) Draw the free body diagrams of the bodies and the pulley. b) (10 Pts.) Find the tensions T, and T2. c) (10 Pts.) Find the moment of inertia I. (g 10 m/s) T2 450

Q4) (25 p)Two objects with masses MA 1 Kg. and Ma 4 are placed on the side surfaces of inclined planes as shown in the figure, where right side is frictionless. They are connected to each other with a rope passing through a pulley with radius R and moment of inertia I. The kinetic friction coefficient on left side is H = 0.01, If the system is moving to right with an acceleration a = 4 m/s. (Both inclined planes have 45°) a) (5 Pts.) Draw the free body diagrams of the bodies and the pulley. b) (10 Pts.) Find the tensions T, and T2. c) (10 Pts.) Find the moment of inertia I. (g 10 m/s) T2 450

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The belt-driven pulley and attached disk are rotating with increasing angular velocity. At a certain 2instant the speed v of the belt is 1.5 m/s, and the total acceleration of point A is 75 m/s . For this instant determine (a) the angular acceleration of the pulley and disk, (b) the total acceleration of point B, and (c) the acceleration of point C on the belt.
Determine the distances x and y for equilibrium if F1 = 800 N and F2 = 1000 N.
The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
4. An open cylindrical tank 2 m in diameter and 4 m high contains water to a depth of 3 m. It is rotated about its own vertical axis with a constant angular speed. a. If w = 8 rad/s, how much water is spilled out and to what depth will the water stand when brought to rest?b.What angular speed w (in rpm) will just zero the depth of water at the center or the tank?c.If w = 100 rpm, how much area at the bottom of the tank is uncovered?
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 60°.
Assume the coefficient of friction = 0.22, A = 175N and B = 96N. Find the least value of P to cause impending motion and the value of θ.
Q3 The space between two square flat parallel plates is filled with oil . Each side of the plate is 720 mm . The thickness of the oil film is 15 mm . The upper plate , which moves at 3 m / s requires a force of 120 N to maintain the speed . Determine : ( 1 ) The dynamic viscosity of the oil ; ( ii ) The kinematic viscosity of oil if the specific gravity of oil is 0.95 .
l=160mm, b=60mm. AB rotating with constant angular velocity 1600 rpm clockwise. determine the velocity of P. θ = 45°
1-Moment of inertia of the pulley (kg.m2) ? 2-tension in rope of m1 (N) ? 3-tension in rope of m2 (N) ? 4-angular acceleration of the pulley (rad/s2) ? 5-acceleration of block m1(m/s2) ? 6-acceleration of block m2 (m/s2) ?
Determine the axial moment of inertia of the rectangle with base b and altitude h about a centroidal axis parallel to the base. Refer to Fig.
Determine the moment of inertia of the shaded area with respect to the x-axis where: b1=0.6 in; b2=1.3 in; t1=0.6 in and h1=1.2 in
a stepladder consisting of two legs pinned together at C is resting on a rough floor. will 800 N worker be able to change the light bulb if he is required to climbed to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. the coefficient of static friction is 0.48