Q4. Two long rods of the same diameter, one of brass(k= 85 W/mK) and the other of copper (k=375 W/mK) have one of their ends inserted in a furnace and the other ends exposed to the same atmosphere. At a distance of 105mm away from the furnace, the temperature of the brass rod is 120' C. Find the distance from the furnace in which the copper rod have the same temperature.

Q4. Two long rods of the same diameter, one of brass(k= 85 W/mK) and the other of copper (k=375 W/mK) have one of their ends inserted in a furnace and the other ends exposed to the same atmosphere. At a distance of 105mm away from the furnace, the temperature of the brass rod is 120' C. Find the distance from the furnace in which the copper rod have the same temperature.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Similar questions

Which spring, the truncated cone spring or the helical spring, would have a larger spring constant? Explain.
A chromel–constantan thermocouple measuring the temperature of a fluid is connected by mistake with copper–constantan extension leads (such that the two constantan wires are connected together and the copper extension lead wire is connected to the chromel thermocouple wire). If the fluid temperature was actually 250 C and the junction between the thermocouple and extension leads was at 90 C, what e.m.f. would be measured at the open ends of the extension leads if the reference junction is maintained at 0 C? What fluid temperature would be deduced from this (assuming that the connection error was not known)?
A metallic ball of radius ro = 5 mm, is initially in equilibrium at 400 C in a furnace. It is suddenly dropped to water at 20 C ( hw = 11003 W/m^2). The properties of the sphere are density= 3000 kg/m3, k = 20 W/m_ K, c = 1000 J/kg K, and α= 6.66E-6 m2/s. Calculate the time required for the center of the sphere to cool to 50 C.
To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)
How long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.
During processing in a steel mill, a 375kg steel casting at 800 degrees is quenched by plunging it into a 500-gal oil bath, which is initially 75 degrees . After the casting cools and the oil bath warms , what is the final tempertature of the two? The weight per unit volume of the oil is 7.5 lb/gal.
A solid rectangular parallelepiped is made of aluminum and is initially at 20 C. The base is a 2 cm by 3 cm rectangle and the height of the parallelepiped is 5 cm. The parallelepiped is now dropped into hot oil at 150 C. Find: a) the temperature of point P and b) the temperature of the center of the parallelepiped after 2 min of exposure to hot oil. Point P is located 1 cm above the center plane and1 cm from each side.
Subject : Thermofluid Question : A wind turbine four 10 cm diameter cups with a center-to-center distance of 40 cm, as shown in Figure 4. Due to a malfunction, the pivot is suddenly stuck, and the cups stop rotating. If the wind speed is 12 m/s moving at the described direction and air density is 1.25 kg/m3. Determine the maximum torque this turbine applies on the pivot.
1. The boiling temperature of water is 100 °C. If you put boiling water in a mugplaced at the table top, you observed that after some time the water cools down,decreasing the temperature of water in the mug. Why is this so? Explain using theZeroth Law of Thermodynamics. What happens to objects when temperature increases? For instance, a jar cover an be removed by putting the cover in hot water. Why is this so?
A mass of ice at -4°C is needed to cool 115 kg of vegetables in a bunker for 24 hours. The initial temperature of the vegetables is assumed to be 29°C. It is also assumed that, within the 24-hr period, the average temperature inside the bunker is 7°C. If the heat gained per hour in the bunker is 30% of the heat removed to cool the vegetables from 29°C to 7°C, what would be the required mass of ice in kg? Use: Specific heat of water 4.2292 kJ/kg-°C Specific heat of ice 1.9387 kJ/kg °C Specific heat of vegetables 3.35 kJ/kg-°C
what is the temperature T at distance X = L1 = 8 cm under the steady-state condition?
The composite wall which is composed of 10 cm brick (k=0.40 W/m2-C), 2 cm cellotex (k=0.03 W/m2- OC), and 6 cm (k=0.30 W/m2-OC),has an outer (brick) temperature T=23 OC and an inner (plaster)temperature T=90 OC. Find the temperature between the cellotex andplaster in OC.