To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)

To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.24P

See similar textbooks

Similar questions

Does the Rankine degree represent a larger or smaller temperature unit than the Kevin degree? Explain.
Most automobiles have a coolant reservoir to catch radiator fluid that may overflow when the engine is hot. Such a radiator, made of copper, is filled to its 12-L capacity when at 10.0°C. -What volume of radiator fluid, in liters, will overflow when the radiator and fluid reach their 99.5°C operating temperature, given that the fluid’s thermal coefficient of volume expansion is 400.0 × 10-6 / °C? The coefficient of volume expansion for copper is 5.1 × 10-5 /°C.
(a) The temperature at the surface of the heating rod, T1. (b) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (c) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (a) and (b), how much the rate of energy transfer to the salt solution ? (d) Compare and discuss the difference of heat transfer with and without the matallic cylinder.
A 30.14 g stainless steel ball bearing at 117.82°C is placed in a constant-pressure calorimeter containing 120 mL of water at 18.44°C. If the specific heat of the ball bearing is 0.474 J/g-°C, calculate the final temperature of the water. Assume the calorimeter to have negligible heat capacity. Specific heat of water is 4.184 J/g-°C .
SUPPOSE THE AMBIENT TEMPERATURE IS 20degrees CELSIUS, AND THE HOT RESERVOIR CONSISTS OF A SPHERICAL TANK WITH A RADIUS OF 4.00 m, THAT ACTS AS AN IDEAL EMITTER OF RADIATION. IF ALL THE RADIANT ENERGY EMITTED BY THE TANK COULD BE CAPTURED, WHAT IS THE AVERAGE AMOUNT OF WORK THAT COULD BE DONE EACH SECOND? ( please only answer if your 100% correct) (show work)
Consider you have four long, 2 cm diameter rods, one each made of copper, steel, wood, and glass. They are to be cooled from a high temperature for 10 minutes. If you want to describe how the temperature changes with time, what approach is best for each of these rods. Balance solution accuracy against efficiency and justify with rules of thumb given
Calculate the capillary effect in mm in a glass tube of 4mm diameter, when immersed in (1)water, (2)mercury. The temperature of the liquid is 25ᵒC and the values of surface tensions of water and mercury at 25⁰C in contact with air is 0.0735 and 0.59N/m respectively. The angle of contact for water is 0ᵒ and 130ᵒ for mercury . Take the density of water 1000 kg/m3 , specific gravity of mercury is 13.6. The capillary effect of water in mm is equal to= The capillary effect of mercury in mm is equal to=
1. The boiling temperature of water is 100 °C. If you put boiling water in a mugplaced at the table top, you observed that after some time the water cools down,decreasing the temperature of water in the mug. Why is this so? Explain using theZeroth Law of Thermodynamics. What happens to objects when temperature increases? For instance, a jar cover an be removed by putting the cover in hot water. Why is this so?
A hollow aluminum cylinder 16.5 cm deep has an internal capacity of 2.000 L at 23.0°C. It is completely filled with turpentine at 23.0°C. The turpentine and the aluminum cylinder are then slowly warmed together to 75.0°C. (The average linear expansion coefficient for aluminum is 2.4 10-5 °C−1, and the average volume expansion coefficient for turpentine is 9.0 10-4 °C−1.) How much turpentine overflows?
Which spring, the truncated cone spring or the helical spring, would have a larger spring constant? Explain.
Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
A copper rod of 30 kg initially at the temperature of 300 °C needs to be immersed and fitted tightly into a ABA alloy ring with inner diameter 30.0015 mm found in tank of 100 liters water of 25 °C. (i) Determine the diameter copper when it is 300 °C. (ii) In your opinion, does the copper rod will still fit tightly into the ABA alloy ring inner diameter 30.0015 in the ambient air condition of 25 °C. Provide your answer in 4 decimal places. Assume the alloy ABA is very small with negligible effect in heat transfer. [Density for copper = 8890 kg/m3, Specific heat, Ccopper = 385 J/kg.°C;Coefficient of thermal expansion, αCopper = 18.0 × 10-6 (°C)-1]. [Density for ABA alloy = 8500 kg/m3, Specific heat, CABA = 138 J/kg.°C;Coefficient of thermal expansion, αABA = 13.3 × 10-6 (°C)-1]. [Density for water = 1000 kg/m3, Specific heat, Cwater = 4200 J/kg.°C].