Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipecharacteristics are as follows: (Take the flow rate equals 0.6m³/sec) and (u = 10-6 m²/sec).%3DPipe1L(m)900D(mm)600e or for CH.w.e 0.25mm300f 0.03f = 0.02CHW. 130215003100040041500750FlowA

Answered: Image /qna-images/answer/ce893619-9be6-4453-8450-50805c195e14.jpg

Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe characteristics are as follows: (Take the flow rate equals 0.6m3/sec) and (u = 10-6 m²/sec). %3D e or for CHw. Pipe 1 L(m) 900 D(mm) 600 e 0.25mm 300 f% 0.03 f = 0.02 CH.W. 130 1500 3 1000 400 4 1500 750 Flow A *の

Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe characteristics are as follows: (Take the flow rate equals 0.6m3/sec) and (u = 10-6 m²/sec). %3D e or for CHw. Pipe 1 L(m) 900 D(mm) 600 e 0.25mm 300 f% 0.03 f = 0.02 CH.W. 130 1500 3 1000 400 4 1500 750 Flow A *の

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

reservoir with water pressurized pipe diameter is 5 cm. The head loss in the system as given by hL= 5V^ 2/ 2g. The height between the water surface and the pipe outlet is 400 m. A discharge of 0.11 m3 /s is needed. What must the pressure in the tank be achieve such a flow rate? Assume a turbulent flow.
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
As seen in Figure 3 below, the water from the tank 1 is pumped to the tank 2 with a flow rate of 5,664 liters/s, passing through a pipe with a diameter of 50.8 mm and a length of 121.92 m. Some of the local losses in the system are also shown on the figure. Calculate the effective power of the pump by taking the relative roughness ɛ / d = 0.001 Note: For all questions, pwater = 1000 kg/m³, g=9.81m/s^2 , the kinematic viscosity of water is 1.0219x106 m²/s and the questions can be solved by accepting the values that are not given.
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Calculate the power required to pump water at 120 kg/s from a supply tank, through an 18 cm diameter galvanised iron pipe to a storage tank located 12m above the supply tank. The length of the pipe is 70 m. All losses other than friction losses are ignored. [Hint: Use Moody Diagram] (For water, ρ = 1000 kg/m3, μ = 1.003 x 10-3 Pa.s)
oil has a spc.gravity of 0.94 with dynamic visc. of U=0.0096 N.sm/^2 flows in a 90 mm diamater pipe at 72 L/s. Find the friction head loss per meter of pipe. Density of Water =1000kg/m^3 1 liter is 0.001 m^3 Use moody diagram
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a commercial steel pipe with an inner diameter of 23.62 inches carries a water flowrate of 600L/sec. The total length of the section is 10m. What is the frictional loss in meters of water at a temperature of 68o F?
Water at 20°C is transported from Tank 1 to Tank 2 at a rate of 0.5m 3 /s via a copperpipe of length 4m and diameter 0.1m. Consider minor losses of a sharp-edged pipe inlet and exit as wellas a fully open globe valve. Determine the following:a) head loss due to friction, hf, through the pipe (estimate hf with Darcy-Weisbach and f with MoodyChart)b) the total head loss, h L, from Tank 1 to Tank 2
The suction water level of a reservoir A is 5m above pump centerline and discharge water level is 50m above pump centerline. The discharge is 2m with suction pipe of 100mm diameter and 90mm diameter discharge pipe. The total head loss is 50% of the velocity head a suction pipe. If pump runs at 360rpm, find the torque developed by the shaft of motor if pump efficiency is 76%. ANSWER: 5.4 KN-m
Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.