Q5: The power of a bus engine is transmitted using the belt-and pulley arrangement shown. If the engine turns pulley A at wa =60 rad/s, determine the angular velocities of the generator pulley B and the air-conditioning pulley C. The hub at D is rigidly connected to B and turns with it. Ans.: wg = 180 rad/s, wc = 360rad/s 100 mm 25 mm wB D 75 mm B 50 mm WA

Q5: The power of a bus engine is transmitted using the belt-and pulley arrangement shown. If the engine turns pulley A at wa =60 rad/s, determine the angular velocities of the generator pulley B and the air-conditioning pulley C. The hub at D is rigidly connected to B and turns with it. Ans.: wg = 180 rad/s, wc = 360rad/s 100 mm 25 mm wB D 75 mm B 50 mm WA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ring C moves downwards at 2 m/s. Determine the value of point B velocity (vB =?), Angular velocity of the arm CB (wBC) and the position vector B in relation to C rB/C for the situation shown in the figure.
The 250 g disk shown spins at the rate w1 = 750 rpm, while axle AB rotates as shown with an angular velocity ω2 of 6 rad/s. Find the Kinetic energy of the disk with this information.
A hoop of radius 95mm and mass 100g is rotated via a capacitor driven power source with P(t)=1.61e-1.3tW. (since it is a hoop, it is a special case, and r=rG) Assuming the hoop is accelerated from rest, determine the rotational velocity after t=8.5s. [rad.s-1] Determine the rotational speed of the hoop after t=8.5s if the power source acts to roll the particle from rest on a horizontal surface. [rad.s-1]
A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is r=4.0m. The velocity of the plate C is VC=6.0 m/s to the right. The velocity of the plate D is VD=2.0 m/s to the left. Using the instantaneous center of zero velocity (IC) to determine (1) The distance between point A and IC point, rA/IC=_____ m
Draw the impulse-momentum diagram and line of action for e. Solve for the following: 1. Determine the angular velocity of the slender bar (B) immediately after impact. angular velocity of A = 57.1 rad/s since there is no external torque 2. Determine the linear velocities of both the sphere (A) and the slender bar (B) immediately after impact at their centroids ANSWERS I GOT BUT ARE INCORRECT: (the unit is given) angular velocity of the slender bar (B) immediately after impact: 8.089 rad/s , 18.49 rad/s linear velocity of the sphere (A) immediately after impact at the centroid: 0.485 rad/s^2, 0.16 rad/s^2, 2.11 rad/s^2 linear velocity of the slender bar (B) immediately after impact at the centroid: 0.485 rad/s^2, 0.49 rad/s^2, 2.21 rad/s^2
A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is r=4.0m. The velocity of the plate C is VC=6.0 m/s to the right. The velocity of the plate D is VD=2.0 m/s to the left. Using the instantaneous center of zero velocity (IC) to determine (3) The magnitude of the angular velocity of the cylinder ω=____________rad/s
The two gears A and B have weights and radii of gyration of WA = 15 lb , kA = 0.5 ft and WB = 15 lb , kB = 0.35 ft, respectively. A motor transmits a couple moment to gear B of M=2(1−e−0.5t)lb⋅ft, where t is in seconds. Determine the angular velocity of gear A in t = 5 s , measured counterclockwise, starting from rest.
Collars A and B are attached by a rod of length 30 cm, as shown below. The joint at A is a ball-and-socket and at B a pin joint. Collar A moves in the z direction, while the guide bar for collar B is on xy plane. At the instant shown, collar A is at a height of 24 cm and collar B is moving with a speed of 3 m/s towards the x axis. Find the (a) angular velocity of the rod, and (b) the sliding of collar B. Use the image attached to solve the question
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 29cm, which carries a mass of reciprocating part whose magnitude is 11kgs with a revolving part of 5kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 500 from top dead centre to bottom dead centre. solve 4 and 5 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 41cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 76cm between the two cylinders in (N-m) 5. Magnitude…
A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is r=4.0m. The velocity of the plate C is VC=6.0 m/s to the right. The velocity of the plate D is VD=2.0 m/s to the left. Using the instantaneous center of zero velocity (IC) to determine (2) The distance between point B and IC point, rB/IC=_____ m
15.8 The gears A, B, and C, of radii rA=500 mm, rB=200 mm, rC=150 mm, respectively, all rotate around fixed axes parallel to the x-axis shown. At a certain instance, gear A rotates with wA=6i rad/s and gear C rotates with aC=10 rad/s2. Determine wB and aB at this instant.
From rest, the motor shaft I rotates to achieve a counter-clockwise angular velocity, ?? = (0.13?3 +3.32?2) rad/s. If no slippage occurs within the system and considering the tabulated given below, determine the velocity and total acceleration of the point 0.3 meter from the center of Disk E, as shown, at ? = 1.22000 second. Also, determine the number of revolutions done by Disk E at the same time.