Q6: Calculate Zin at the load using smith chart for total transmission lines, while the wavelength is 10 cm for two lines? 2.4 cm 3.5 cm Z01 = 100 N Zo2 = 752 R = 150,0 Zin

Q: For10 m long lossless transmission line L=0.25µH/m and C=100pF/m. It is operating at 600MHZ. Find…

A: The wave is function of space and time. The EM wave is formed when electric field is in contact with…

Q: The voltage waveform on a lossless TL in air is given by: V(z)=150e 8z + -20e*Bz (V). The TL has a…

A: Given: Voltage, Vz=150e-jβz+-20ejβz V Characteristic impedance, Z0=100 Ω Length, L=0.5 λ

Q: 2) What is the length of the transmission line in wavelengths from the load, such that the…

A: For a lossless coaxial transmission line of characteristic impedance 50 Ω and a wave phase velocity…

Q: Smith Chart A quarter-wave lossless 100 N line is terminated by a load Z, the receiving end is 80 V,…

A: for quarter wave length l=λ4=xcharacterstic impedance z0=100Ωload impedance zl=210Ω Line current…

Q: Q5: A 50-W lossless line terminated in a purely resistive load has a voltage standing wave ratio of…

A: Here we need to find reflection coefficient first and then we can find ZL.

Q: For multimode step-index fiber with core index of 1.68 and radius of 35 um. The index difference is…

A: Write down the given variables:-  a = 35 μmλ = 1150 nmn1 = 1.68 The refractive index of cladding is…

Q: u Vm in air normally hits lossless a medium H, = 1, ɛ, = 4) at z = 0. TA8 The SWR s is (A) 2 (B) 1…

A:

Q: lossless transmission line has a characteristic impedance of Zo=40N, load reflection coefficient is…

A:

Q: find the inductance per km of a three-phase transmission line using 0.2 cm diameter conductors when…

A: Given Data: D = distance between the condutor = 1m Radius of the conductor r = 0.2 / 2 = 0.1 cm = 1…

Q: factor . The arrangement of conductors of a single-phase transmission line is shown below, the…

A:

Q: A factor affecting corona in transmission line related to the conductor among the options is length…

A:

Q: The 0.1A length line has a characteristic impedance of 502 and is terminated with a load impedance…

A: Given data: load impedence ZL=5+j25 ohm. characteristic impedence Z= 50 ohm With the help of smith…

Q: On a 150-2 lossless transmission line, the following observations were noted: distance of first…

A: The solution can be achieved as follows.

Q: If the reflection co-efficient for a transmission line is 0.3, then the VSWR is: a) 0.5384 b) 1.8571…

A: Given information: For a transmission line, the value of the reflection coefficient is Γ=0.3

Q: A loss less transmission line of length 3.125m with characteristic impedance 502, is operating on…

A: Note :- As per guidelines we are supposed to answer only three subparts at a time. So, I request you…

Q: characteristic impedance of Zo=302, load reflection coefficient is 0.5 .What is the load impedance?

A:

Q: A 3-phase transmission line using 20 mm diameter conductor. When these conductors are placed at the…

A: As per the guidelines of Bartleby we supposed to answer first question for remaining questions we…

Q: A lossless 1000 line is terminated with an inductance L=2mH. At w=25×10³rad/s, what is the…

A: In this question,  We need to determine the reflection coefficient at the end of the line  If…

Q: Problem 14. A long transmission line has a char- acteristic impedance of (500-j40) № and is termin-…

A: Given a long transmission line with, Characteristics impedance, ZO=500-j40 Ω Terminated in an…

Q: A transmission line has characteristic impedance of 75 Ω and it is connected to receiver with Zr=…

A:

Q: 2-2m. If Vs = 100 volts, find: (use crack diagram) A lossless transmission line having Z-5002,…

A: Given: Z0=50 ΩVS=100 VKr=0.4<45λ=2 Find: 1. Standing wave ratio 2.Voltage standing pattern

Q: 10/Explain in your own words and your own understanding (avoid plagiarism) why there's Capacitance…

A: Simply capacitor is nothing but two conducting materials separated by small distance, in between…

Q: At a frequency of 4 MHz a parallel wire transmission line has the following parameters: R = 0.025…

A:

Q: Q6: Calculate Zin at the load using smith chart for total transmission lines, while the wavelength…

A:

Q: c. A lossless 502line is terminated by a load Zı = 75 + j60 2. Using a Smith chart, determine (a)…

A: Given Zo = 50 ohm ZL = 75+j60 ohm

Q: For multimode step-index fiber with core index of 1.68 and radius of 35 um. The indexdifference is…

A:

Q: A time domain reflectometer (TDR) of output impedance 50- sends a step voltage down a 50-2…

A: At t =0 (no reflection )   At V(0)  = 50100 Vs Given from figure at t=06=12Vs=12 V (source voltage…

Q: A 3-phase transmission line has its conductors at the corners of an equilateral triangle with side 3…

A: we need to find out inductance of the line per phase per km.

Q: For a single mode fiber with V = 1.3526, b = 0.1652, n1 = 1.468, n2 = 1.46612, and a = 4.5 um,…

A: Given, V = 1.3526 b = 0.1652 n1 = 1.468  n2 = 1.46612 a= 4.5 um

Q: Explain: “A good transmission line is a bad antenna, while a bad transmission line is a good…

A: Given :    Antenna is a transducers which will convert the one form of energy into another form of…

Q: The effect of rain attenuation at high frequencies is minimized if vertical polarization is used.…

A: The attenuation in the communication process which is caused by rain is known as rain attenuation…

Q: Assume a transmission line with ZL = 85 + j45 Ω and Zo = 30 Ω. If the frequency of the line is…

A: According to the bartleby's guidelines we have to solve only first three subparts of a question so…

Q: PROBLEM NO. 1 Find the Inductance in Henry per meter of a Three-Phase Transmission Line using 1.5 cm…

A: In three phase transmission line the inductance is defined as: GMR:  It is called Geometric Mean…

Q: Derive the following formula for a transmission line's voltage reflection coefficient (all symbols…

A:

Q: line is terminated in -10 volts, use Smith A lossless T.L of 10.25m long with Z-50 2. The…

A:

Q: In medium transmission line, capacitance is considered as O a. Lumped parameter O b. Distributed…

A: Given :    Generally  depending on the type of the medium we classify them parameters.   Distributed…

Q: A 50Ω transmission line uses an insulating material with ǫr = 3. When terminated in an open circuit,…

A:

Q: for coverage P. and outa distance of 1

A: Solution

Q: Problem 14. A long transmission line has a char- acteristic impedance of (500-j40) S2 and is termin-…

A: Given data, Characteristics impedance Z0=500-j40 Ω Load impedance ZL=500+j40 Ω

Q: In line capacitance is neglected due to Select one: O a. Short transmission line, smaller length and…

A: The question is from transmission and distribution topic.

Q: what is expected VSWR for a transmission line with a reflection coefficient of 0.377

A: Given data Reflection coefficient is τ=0.377 Calculating expected VSWR…

Q: On a 144 N lossless transmission line, the following observations were noted: distance of first…

A: Given Characteristic impedance is Zo=144Ω,  Distance of first voltage minimum to the load is 3cm…

Q: A transmission line has a characteristic impedance of 300 N and is terminated in a load of 300 -…

A:

Q: Find the Inductance per meter of a Three-Phase Transmission Line using 1.32 cm diameter conductors…

A:

Q: An antenna with a radiation resistance of 48 ohms, a loss resistance of 2 ohms, and a reactance of…

A:

Q: If a transmission line of characteristics impedance of Zo= 50 2 is terminated with a load impedance…

A: Given: Characteristics impedance, Zo=50 Ω Load impedance, ZL=100 Ω

Q: 4-12. The electric field intensity of the dominant TE10 mode in a lossless rectangular wave- guide…

A:

Q: A lossless transmission line (TL) has a characteristic impedance of Zo= 250 N, a load impedance of…

A: According to guidelines, we need to solve only the first three subparts. Given Zo = 250 ohm , ZR=…

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.