A transmission line has a characteristic impedance of 300 N and is terminated in a load of 300 - j300 N. The propagation constant of the line is 0.054 + j3.53 per meter. Determine: a. The reflection coefficient at the load b. The transition coefficient at the load c. The reflection coefficient at a point 2 m away from the load

A transmission line has a characteristic impedance of 300 N and is terminated in a load of 300 - j300 N. The propagation constant of the line is 0.054 + j3.53 per meter. Determine: a. The reflection coefficient at the load b. The transition coefficient at the load c. The reflection coefficient at a point 2 m away from the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

In terms of line-to-line capacitance, the line-to-neutral capacitance of a single-phase transmission line is Same Twice One-half
A load has a reflection coefficient of 0.5 when referred to 50 Ω. The load is at the end of a line with a 50 Ω characteristic impedance.(a) If the line has an electrical length of 45 degrees, what is the reflection coefficient calculated at the input of the line?(b) What is the VSWR on the 50 Ω line?
A transmission line with 0.4? line length and 50 Ω characteristic impedance is terminated with load impedance ZL = 40-j30 Ω. For this transmission linea) Using transmission line equations, b) Using Smith Chart,Find the sizes.I. Standing Wave Ratio in Line (DDO)ii. Reflection coefficient in loadiii. Load admittanceiv. Line input impedance
The observed standing-wave ratio on a 100-Ω lossless line is 8. If the first maximum voltageoccurs at 0.3λ from the load, calculate the load impedance and the voltage reflection coefficientat the load. (use smith chart) How do you use a smith chart to solve this?
The capacitance per unit length and the characteristic impedance of a lossless Transmission line are C and Z0 respectively. Express the velocity of travelling wave on the transmission line in terms of the two given parameters above.
A short-circuited transmission line section is exactly one-quarter wavelengthat a frequency of 1250 MHz. Calculate the inductave reactance , and (b) the eq uiva le nt inductance, at a frequency of 500 MHz. The character st ~ impedance of the line is 50ohm
A 105MHz, 90 v peak signal is incident on a 50-ohm transmission line. The line is 125m long and is terminated in 300-ohm load. What is the SWR for this situation? Find the reflection coefficient.
A transmission line in air with characteristic impedance Z0=50 ohm is terminated with a load impedance ZL ohm. What is the propogation constant k of the transmission line (assuming a coaxial line) for a 100 MHz uniform plane wave? What is the equivalence impedance of Z(-l) at l=.75m when ZL=25-j200 ohm? Calculate the shunt admittance to be added at l=.75m so that the line matched.
In a three-phase transmission line with a length of 150 km, a voltage of 250 kV and a frequency of 50 Hz, the diameter of the steel-cored aluminum conductors is 18 mm, the roughness coefficient of the conductors is 0.6, and the spacing between the conductors is 6 m. Since the average air temperature is 27˚ C and the air pressure is 762 mmHg along the line, find the corona voltage around the conductor and the total loss of the line according to the Peek formula.
The impedance and propagation constant at 241 MHz for a transmission line are Z0 = 43 - j2 Ω and γ=2 + j7 m-1. Determines the parameters per unit length of the line.
1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
A lossless transmission line has a Zo of 50 ohms and a line velocity of 2.4 x 10^8 m/s. If the operating frequency is 1 MHz. Determine the capacitance in pf.