Q8) A two-pole de generator has an armature containing a total of 40 conductors connected in two parallel paths. The flux per pole is 0.02 web, and the speed of the prime mover is 30 rpm. The resistance of each conductor is 0.01 ohm, and the current-carrying capacity of each conductor is 10 A. Calculate:

Q8) A two-pole de generator has an armature containing a total of 40 conductors connected in two parallel paths. The flux per pole is 0.02 web, and the speed of the prime mover is 30 rpm. The resistance of each conductor is 0.01 ohm, and the current-carrying capacity of each conductor is 10 A. Calculate:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.11P

See similar textbooks

Similar questions

Q2)A. Explain compound DC generator, also describe its types and terminal characteristics of compound DC generator. proper explanation and diagram
A 4-pole lap winding generator with 16 slot, 42 conductor per slot, 480v runs at 1800rpm. Find the flux produced per pole
A 4 pole dc shunt generator with a shunt field resistance of 100 ohm and an armature resistance of 1 ohm has 378 wave connected conductor in its armature. the flux per pole is 0.02wb, if the load resistance of 10 ohm is connexted across the aemature terminal and the generator driven at 1000rpm, calculate the power obsorbed by load
111/ The armature reaction of the DC generator reduces the generated EMF. Select one: True False
the lap wound armature of a six pole generator has600 active conductors. The speed is 1000rpm. The area of each pole face is 100 sq. in. and the average air gap flux density under the pole face is 8000 gauss. Calculate the emf between the positive and negative brushes.
A long-shunt compound generator delivers a load current of 50A at 500V and has armature, series field and shunt field resistances of 0.05 ohms, 0.03 ohms and 250 ohms respectively. Calculate the generated voltage and the armature current. Allow 1V per brush for contact drop.
A 4-pole, 36-slot, 60-Hz, three-phase, Y-connected, synchronous generatorhas 10 turns per coil. The flux per pole is 50 mWb. For a series connection,determine (a) the synchronous speed, (b) the per-phase voltage, and (c) theline voltage
A 20 kW, 440-V, short-shunt, compound d.c. generator has a full-load efficiency of 87%. If theresistance of the armature and interpoles is 0.4 Ω and that of the series and shunt fields 0.25 Ωand 240 Ω respectively, calculate the combined bearing friction, windage and core-loss of themachine.
A short shunt compound DC generator supplies a load of 10A at a voltage of 10 volts. If the resistances of Armature, shunt field and series field windings are 0.01 ohm, 1 ohm and 0.00 ohm respectively. c) Write down the factors to improve the generated voltage.
A long shunt generator delivers 25kW at 220V. The shunt, series and armature resistances are 50ohms, 0.02ohms, and 0.05ohms respectively, calculate the generated emf.
A short shunt compound generator supplies a load of 10 kW at 200 V through a pair of feeder and series field resistance 0.10 ohm. Armature resistance, shunt field resistance and series field resistance are 0.01 ohm, 52.2 ohms and 0.10 ohm, respectively. If the core friction and windage losses amount to 631 watts, the BHP of the driving engine is nearest to
A d.c. shunt-wound generator running at 10rps generates a voltage of 150V at a certain value of field current. Determine the change in the generated voltage of same generator when running at 5rps, the field current is reduced by 50 percent, assuming the flux is proportional to the field current